Tilt Lever - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-9758     | 千斤顶台架总成     | 1     |
G     | 3S-6224     | 电动液压泵     | 1     |
6V-3175 | 双作用油缸     | 1     | |
4K-0684 | 硬垫圈     | 1     | |
9S-5431 | 套筒     | 1     | |
4C-9634 | 拔销器螺柱     | 1     | |
1P-0544 | 高速螺母组件     | 1     | |
1P-1844 | 轴承拉拔器     | 1     | |
H     | 1P-0520     | 冲头总成     | 1     |
J     | 5P-0960     | 润滑脂筒     | 1     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上,从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 降低倾斜连杆的轴承温度。 使用工具 (G) 在倾斜连杆中安装轴承 (4) 。 将轴承安装到 10.0 ± 1.0 mm (0.39 ± 0.04 inch) 的深度。
Show/hide table
图 1 | g01164196 |
注: 安装之前,用工具 (J) 润滑孔、销和唇形密封。
- 利用工具 (H) 安装唇形密封 (9) 。 请确保密封的唇朝外。
Show/hide table
图 2 | g00349673 |
Show/hide table
图 3 | g01164198 |
- 对于倾斜连杆另一侧上的唇形密封重复步骤2。
- 使用适当的起吊设备定位倾斜连杆 (4) 。 倾斜杆 (4) 的重量约为 380 kg (840 lb)。
注: 对齐倾斜连杆和提升臂的孔非常重要。 对齐不正确可导致销安装过程中唇形密封损坏。
Show/hide table
图 4 | g00395779 |
- 小心安装销组件 (8) 。
Show/hide table
图 5 | g00349652 |
- 安装垫圈、垫片和固定销组件 (8) 的螺栓 (7) 。
- 安装销组件 (6) 。
Show/hide table
图 6 | g00395724 |
注: 对齐倾斜连杆和铲斗倾斜连杆的孔非常重要。 对齐不正确可导致销安装过程中唇形密封损坏。
- 安装垫圈、垫片和固定销组件 (6) 的螺栓 (5) 。
- 使用合适的起吊设备提升倾斜油缸的杆端。 倾斜油缸的重量约为 220 kg (485 lb)。
Show/hide table
图 7 | g00349492 |
典型示例 |
- 起动发动机。 扩展倾斜油缸。
- 对齐倾斜油缸的孔与倾斜杆的销孔。 安装销组件 (3) 。
- 安装垫圈和螺栓 (2) ,以便把销组件 (3) 固定在倾斜连杆上。
- 拆下工具 (A) 。
Show/hide table
图 8 | g00342992 |
End By: 安装倾斜位置传感器和支架。 拆装, "倾斜位置传感器及支架(作业机具定位器控制)-卸下和安装"。
Caterpillar Information System:
966H and 972H Wheel Loaders Machine Systems Tilt Lever - Remove
2005/04/18 Improvements to the Radiator Guard Are Now Used {7155}
2005/04/11 Correction to Troubleshooting "Fuel Actuator" {1716}
980H Wheel Loader Electrohydraulic System MID 082 - CID 0350 - FMI 13
980H Wheel Loader Electrohydraulic System MID 082 - CID 0350 - FMI 08
980H Wheel Loader Electrohydraulic System MID 082 - CID 0350 - FMI 04
980H Wheel Loader Electrohydraulic System MID 082 - CID 0350 - FMI 03
980H Wheel Loader Electrohydraulic System MID 082 - CID 0350 - FMI 01
980H Wheel Loader Electrohydraulic System MID 082 - CID 0350 - FMI 00
621G and 627G Wheel Tractor-Scrapers Machine Systems Hydraulic System Pressure - Release
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 1393 - FMI 04
637G Wheel Tractor-Scraper Fuel System Secondary Filter - Replace
980H Wheel Loader Electrohydraulic System MID 082 - CID 0357 - FMI 03
980H Wheel Loader Electrohydraulic System MID 082 - CID 0357 - FMI 05
980H Wheel Loader Electrohydraulic System MID 082 - CID 0357 - FMI 06
980H Wheel Loader Electrohydraulic System MID 082 - CID 0357 - FMI 13
973C Track-Type Loader Engine Crankcase Breather - Clean
Improving the Environment of the Operator{7301} Improving the Environment of the Operator{7301}
657G Wheel Tractor-Scraper Fuel System - Prime
994F Wheel Loader Hydraulic System Electronic Control Module (ECM) - Configure
980H Wheel Loader Electrohydraulic System MID 082 - CID 0359 - FMI 03
980H Wheel Loader Electrohydraulic System MID 082 - CID 0359 - FMI 05
980H Wheel Loader Electrohydraulic System MID 082 - CID 0359 - FMI 06
2005/04/04 Improved Air Conditioner Compressor Guard is Now Used {1805}