Lift Arms - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 8S-7630     | 台架     | 2     |
8S-7641 | 管     | 2     | |
8S-7615 | 销     | 2     | |
8S-8048 | 鞍座     | 2     | |
B     | 3S-6224     | 电动液压泵     | 1     |
6V-3175 | 双作用油缸     | 1     | |
4C-9634 | 拔销器螺柱     | 1     | |
4K-0684 | 硬垫圈     | 1     | |
9U-6832 | 高速螺母组件     | 1     | |
1P-1839 | 轴承拆卸工具适配器     | 1     | |
C     | 3S-6224     | 电动液压泵     | 1     |
6V-3175 | 双作用油缸     | 1     | |
4C-9634 | 拔销器螺柱     | 1     | |
4K-0684 | 硬垫圈     | 1     | |
9U-6832 | 高速螺母组件     | 1     | |
1P-1837 | 轴承拆卸工具适配器     | 1     | |
D     | 3S-6224     | 电动液压泵     | 1     |
6V-3175 | 双作用油缸     | 1     | |
4C-9634 | 拔销器螺柱     | 1     | |
4K-0684 | 硬垫圈     | 1     | |
9U-6832 | 高速螺母组件     | 1     | |
1P-1835 | 轴承拆卸工具适配器     | 1     | |
E     | 1P-0520     | 冲头总成     | 1     |
F     | 1P-0510     | 冲头总成     | 1     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上,从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
- 在安装之前降低提升臂轴承的温度。
- 使用工具 (B) 将轴承安装到提升臂装载机机架的端部。 将轴承安装到 9.5 ± 1.0 mm (0.37 ± 0.04 inch) 的深度。
Show/hide table
图 1 | g00352054 |
- 利用工具 (C) 将轴承装入提升油缸销孔中。 将轴承安装到 9.5 ± 1.0 mm (0.37 ± 0.04 inch)的深度。
Show/hide table
图 2 | g00352056 |
- 使用工具 (D) 将轴承安装到提升臂铲斗端部。 将轴承安装到 9.5 ± 1.0 mm (0.37 ± 0.04 inch) 的深度。
Show/hide table
图 3 | g00352058 |
- 使用工具 (E) 和工具 (F) 把唇形密封 (17) 安装到提升臂 (15) 的两侧。
Show/hide table
图 4 | g01156782 |
- 使用适当的起吊设备把提升臂 (15) 定位到正确位置。 提升臂 (15) 的重量约为 1390 kg (3065 lb)。
Show/hide table
图 5 | g01156754 |
- 安装销组件 (16) 、垫片、垫圈和螺栓。
Show/hide table
图 6 | g01156823 |
- 对于机器另一侧的销组件,重复步骤7。
- 使用适当的起吊设备把提升臂降低到工具 (A) 上。
Show/hide table
图 7 | g00351252 |
- 安装把线束组件 (13) 固定在提升臂上的夹子 (14) 和支架。
Show/hide table
图 8 | g01156753 |
- 使用螺栓 (11) 连接软管组件 (12) 。
- 使用螺栓 (9) 连接软管组件 (10) 。
Show/hide table
图 9 | g01156764 |
- 安装螺栓 (8) 并连接管组件 (7) 。
Show/hide table
图 10 | g01156752 |
- 定位照明组件 (6) 并安装螺栓 (5) 。
Show/hide table
图 11 | g01156751 |
- 连接线束组件 (4) 。
- 使用适当的起吊设备定位提升油缸 (3) ,如图所示。 提升油缸 (3) 的重量约为 250 kg (550 lb)。
Show/hide table
图 12 | g00398799 |
- 安装销组件 (2) 、螺栓 (1) 和垫圈。
- 从用于支撑提升油缸 (3) 的机架上拆下挡块。
- 在提升臂的另一侧重复步骤13到18。
- 升起提升臂后拆下工具 (A) 。
End By:
- 安装提升位置传感器和支架。 请参阅 拆装, "提升位置传感器和支架(提升限位控制-卸下和安装"。
- 安装倾斜油缸。 请参阅 拆解和组装, "倾斜油缸 - 安装"。
- 安装倾斜连杆。 请参阅 拆解和组装, "倾斜连杆 - 安装"。
- 安装铲斗。 请参阅 拆解和组装, "铲斗 - 安装"。
- 安装倾斜连杆。 请参阅 拆解和组装, "倾斜连杆 - 安装"。
Caterpillar Information System:
966H and 972H Wheel Loaders Machine Systems Lift Arms - Remove
AD45B Underground Articulated Truck Power Train Electronic Control System MID 027 - CID 0190 - FMI 08
AD45B Underground Articulated Truck Power Train Electronic Control System MID 027 - CID 0190 - FMI 02
657G Wheel Tractor-Scraper Cutting Edges and End Bits - Inspect/Replace
631G Wheel Tractor-Scraper Engine Oil Level - Check
657G Wheel Tractor-Scraper Cooling System Pressure Cap - Clean/Replace
637G Wheel Tractor-Scraper Engine Oil (High Speed) and Oil Filter - Change
904B Wheel Loader Engine Supplement Water Temperature Regulator - Remove and Install
C9 Engines for Caterpillar Built Machines Fan Drive - Remove
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0489 - FMI 03
631G Wheel Tractor-Scraper Engine Oil (High Speed) and Oil Filter - Change
657G Wheel Tractor-Scraper Cooling System Coolant Sample (Level 1) - Obtain
637G Wheel Tractor-Scraper Engine Oil Level - Check
631G Wheel Tractor-Scraper Engine Oil Sample - Obtain
2005/04/18 A New Aftercooler Gasket and a New Torque Tightening Sequence is Now Used {1063}
Machining of Replacement Sleeve Bearings{1206, 1212, 1234} Machining of Replacement Sleeve Bearings{1206, 1212, 1234}
637G Wheel Tractor-Scraper Engine Oil Sample - Obtain
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System MID 082 - CID 0489 - FMI 04
904B Wheel Loader Power Train Worksheets
953C Track-Type Loader Front Idler Position - Check
904B Wheel Loader Engine Supplement Water Pump - Remove and Install
992G Wheel Loader Maintenance Interval Schedule
854G Wheel Dozer Maintenance Interval Schedule
657G Wheel Tractor-Scraper Differential and Final Drive Breather - Clean