3508B, 3512B and 3516B Generator Set Engines Caterpillar


Exhaust Elbow - Remove and Install

Usage:

3516B JCH

拆卸步骤

表 1
所需工具    
工具     零件号     零件描述     数量    
A     138-7573     连杆支架     2    

开始:

  1. 拆下涡轮增压器。 请参阅拆解和组装, "涡轮增压器 - 拆卸"。


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。





    图 1g01141406

  1. 将工具 (A) 安装到排气弯管 (1) 上。 将适当的起吊设备连接到工具 (A) 上。 排气弯管 (1) 的重量约为 48 kg (106 lb)。

  1. 拆下螺栓 (2) 。 拆下排气弯管 (1) 。



    图 2g01141408

  1. 拆下卡箍 (3) 。 从管组件 (7) 的每端拆下卡箍 (6) 。 拆下管组件 (7) 。 从管组件上拆下 O 形密封圈。

  1. 将适当的起吊设备连接到设备托架 (5) 上。 设备托架 (5) 的重量约为 117 kg (257 lb)。

  1. 拆下螺栓 (4) 。 拆下设备托架 (5) 。

安装步骤

表 2
所需工具    
工具     零件号     零件描述     数量    
A     138-7573     连杆支架     2    


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。





    图 3g01141408

  1. 将适当的起吊设备连接到设备托架 (5) 上。 设备托架 (5) 的重量约为 117 kg (257 lb)。 定位设备托架 (5) ,然后安装螺栓 (4) 。

  1. 将 O 形密封圈安装在管组件 (7) 上。 定位管组件 (7) ,然后安装卡箍 (6) 。

  1. 安装卡箍 (3) 。



    图 4g01141406

  1. 将工具 (A) 安装到排气弯管 (1) 上。 将适当的起吊设备连接到工具 (A) 上。 排气弯管 (1) 的重量约为 48 kg (106 lb)。 定位排气弯管 (1) ,并安装螺栓 (2) 。

End By: 安装涡轮增压器。 请参阅 拆解和组装, "涡轮增压器 - 安装"。

Caterpillar Information System:

3500 Engines Auxiliary Water Pump - Assemble
3500 Engines Auxiliary Water Pump - Disassemble
Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736} Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736}
3508C, 3512C and 3516C Marine Engines Auxiliary Water Pump - Remove
DE Series Generator Set with Cat C1.1, C1.5, and C2.2 Engines Generator Lead Connections
2005/04/25 Cover Plate, Flange are Available for Use During Flow Tests on the Main Hydraulic Pumps {0738, 5070, 5084}
C1.5 GEN SET Electric Power Generation Refill Capacities and Recommendations
2013/09/27 Test Kit Allows Technician to Check Air Systems with Bendix Air Compressors {0701, 1803}
Electronic Installation Guide{1000} Electronic Installation Guide{1000}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201} Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
2005/02/21 Information Release Memo, PELJ0481 , "Product Line Expansion for Caterpillar Low and Medium Pressure Hose and Coupling Products" {5057}
C9 Urban Transit Bus Engine Air Compressor - Remove and Install
374F Excavator Bucket Linkage - Inspect/Adjust
C15 and C18 Engines for Caterpillar Built Machines Diagnostic Codes
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C27 and C32 Engines for Caterpillar Built Machines E194 High Exhaust Temperature
C27 and C32 Generator Set Engines E361 High Engine Coolant Temperature
C27 and C32 Engines for Caterpillar Built Machines E362 Engine Overspeed
345C MHPU Mobile Hydraulic Power Unit Hydraulic System Fan Motor (Hydraulic and Radiator Cooling)
C27 and C32 Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure
3508C, 3512C and 3516C Marine Engines Engine Oil Pump - Remove
3508C, 3512C and 3516C Marine Engines Engine Oil Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Quality - Test
C4.4 (Mech) Industrial Engine Cooling System - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.