Piston Pump (Left Propel) - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
ZZ     | 6V-9511     | Face Seal Plug (1 3/16 - 12 THD)     | 4     |
6V-9832 | Cap Assembly (1 3/16 - 12 THD)     | 4     | |
6V-9512 | Face Seal Plug (1 7/16 - 12 THD)     | 2     | |
6V-9833 | Cap Assembly (1 7/16 - 12 THD)     | 2     |
Start By:
- Remove the piston pump (left drag conveyor and right auger conveyor). Refer to Disassembly and Assembly, "Piston Pump (Left Drag Conveyor and Right Auger Conveyor) - Remove".
- Remove the piston pump (hydraulic generator), if equipped. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic Generator) - Remove".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
- Drain the oil from the pump drive into a suitable container. Refer to Operation and Maintenance Manual for the correct procedure.
- Disconnect harness assemblies (1) from piston pump (2) .
Show/hide table
Illustration 1 | g01141395 |
- Disconnect hose assemblies (3) from piston pump (2) .
Show/hide table
Illustration 2 | g01141394 |
- Disconnect hose assemblies (4) from piston pump (2) .
- Disconnect hose assemblies (5) from piston pump (2) .
- Attach a suitable lifting device to piston pump (2). Remove bolts (6) and remove piston pump (2) from the machine. The weight of piston pump (2) is approximately 77 kg (170 lb).
Show/hide table
Illustration 3 | g01141396 |
- Remove the O-ring seal from piston pump (2) .
Caterpillar Information System:
PM-201 Cold Planer Rotor Service Door Cylinder Pins - Lubricate
PM-201 Cold Planer Propel System Track
PM-201 Cold Planer Track Tension - Check/Adjust
PM-201 Cold Planer Upper Conveyor Lift Cylinder Mount - Lubricate
3500 Engines Auxiliary Water Pump - Assemble
3500 Engines Auxiliary Water Pump - Disassemble
PM-201 Cold Planer Upper Conveyor Belt (Second Stage) Tension and Tracking - Adjust
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Hood and Engine Enclosure - Install
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Hood and Engine Enclosure - Remove
793D Off-Highway Truck/Tractor Electronic Control Module (Integrated Brake) - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Engine Supplement Refrigerant Compressor - Remove and Install
Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736} Reuse Guideline for Hydraulic Cylinder Position Sensor {5574, 5736}
PM-201 Cold Planer Propel System Idlers (Track)
PM-201 Cold Planer Rotor Drive Belt - Inspect
PM-201 Cold Planer Propel System Hydraulic Tank
PM-201 Cold Planer Propel System Track Adjuster and Recoil
PM-201 Cold Planer Rotor Cutter Bits - Inspect/Replace
793D Off-Highway Truck/Tractor Screen (Hoist Pump) - Remove
793D Off-Highway Truck/Tractor Screen (Hoist Pump) - Install
PM-201 Cold Planer Indicators and Gauges - Test
C11 and C15 Engines for Caterpillar Built Machines Cat Data Link Circuit - Test
PM-201 Cold Planer Propel System Track Roller
CP76 and CS76 Vibratory Compactors Propel System Hydraulic Oil Filter
PM-201 Cold Planer Propel System Final Drive Planetary