Engine Oil Cooler - Disassemble
开始:
- 拆下发动机机油冷却器。 请参阅拆解和组装, "发动机机油冷却器 - 拆卸"。
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 拆下螺栓 (7)。 拆下弯头 (6)。 从弯头上拆下密封垫 (8)。
- 从弯头 (6) 上卸下管 (4)。 将 O 形密封圈 (5) 从管 (4) 上拆下。
- 将螺栓和护盖 (9)从弯管 (6)上拆下。 从弯头上卸下密封垫。
- 在机油冷却器底盖 (3) 上和发动机机油冷却器芯 (1) 上进行标记供组装时参考。 拆下螺栓 (10)，然后将机油冷却器底盖 (3)从发动机机油冷却器芯 (1)上拆下。 将密封垫 (2)从发动机机油冷却器芯上拆下。
Show/hide table
图 2 g01135795 - 在机油冷却器底盖 (14) 上和发动机机油冷却器芯 (1) 上进行标记供组装时参考。 拆下螺栓 (13)，然后将机油冷却器底盖 (14)从发动机机油冷却器芯 (1)上拆下。 将密封垫 (16)从发动机机油冷却器芯上拆下。
- 从发动机机油冷却器旁通拆卸螺栓 (11) 和弯头 (12)。 将 O 形密封圈从弯头上拆下。
- 拆下盖 (17) 和 O 形密封圈。
- 如有必要，拆下排油塞 (15)和 O 形密封圈。
- 彻底清洁发动机机油冷却器芯中的管。
Show/hide table
图 3 g01135796 Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 将螺栓 (22)、护盖 (21)、O 形密封圈 (18)、弹簧 (19)以及旁通阀 (20)从弯管 (12)上拆下。
Show/hide table
| |
| 图 1 | g01135749 |
Caterpillar Information System:
3516B and 3516B High Displacement Engines for 994D and 994F Wheel Loaders Fuel Filter Base - Electric Fuel Priming Pump
C11 and C13 Engines for Caterpillar Built Machines Electronic Unit Injector - Remove
3406E, C12, C15 and C18 Marine Engines CID 0096 FMI 04 Fuel Level Sensor short to ground
3406E, C12, C15 and C18 Marine Engines CID 0096 FMI 03 Fuel Level Sensor open/short to +batt
Particulate Filter for Stationary Engines in Standby Applications{1091} Particulate Filter for Stationary Engines in Standby Applications{1091}
3500B Marine Propulsion Engines Auxiliary Water Pump - Inspect
3306B Industrial Engine Emergency Stopping
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Install
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Remove
3412E Petroleum Engine CID 1835 FMI 04 Auxiliary Pressure Sensor short to ground
3412E Petroleum Engine CID 1835 FMI 03 Auxiliary Pressure Sensor open/short to +batt
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Factory Passwords
3508C, 3512C and 3516C Marine Engines Engine Oil Cooler - Assemble
345C Excavator Machine System Specifications Boom Cylinder
C11 and C13 Engines for Caterpillar Built Machines Electronic Unit Injector - Install
3500B Marine Propulsion Engines Sea Water Strainer - Clean/Inspect
3500B Marine Propulsion Engines Heat Exchanger - Inspect
3176C and 3196 Engines for Caterpillar Built Machines Atmospheric Pressure Sensor
3126B Industrial Engines E004 Engine Overspeed Shutdown
2005/01/17 Correction to Engine Speed/Timing Sensor-Calibrate {1912}
3406E, C12, C15 and C18 Marine Engines E015 High Engine Coolant Temperature Derate
3406E, C12, C15 and C18 Marine Engines E017 High Engine Coolant Temperature Warning
3126B Industrial Engines E025 High Inlet Air Temperature Derate
3508C, 3512C and 3516C Marine Engines Crankshaft Rear Seal and Wear Sleeve - Install