3508B, 3512B and 3516B Generator Set Engines Caterpillar


Turbocharger - Install

Usage:

3516B JCH

安装步骤

表 1
所需工具    
工具     零件号     零件描述     数量    
A     5P-3931     防粘结剂     -    
B     1U-6396     O 形圈组装固定胶     -    


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。





    图 1g01116799

  1. 将适当的起吊设备连接到涡轮增压器 (8) 上。 3508B 涡轮增压器的重量约为 24 kg (53 lb)。 定位涡轮增压器 (8) ,然后安装螺栓 (4) 。

    注: 3512B 涡轮增压器的重量约为 30 kg (66 lb)。 3516B 涡轮增压器的重量约为 47 kg (104 lb)。

  1. 将新密封垫 (6) 安装到排气歧管 (5) 和涡轮增压器之间。 将密封垫安置在排气歧管上。 在螺栓 (4) 的螺纹上使用工具 (A) 。 安装螺栓 (4) ,并拧紧至扭矩为 54 ± 5 N·m (40 ± 7 lb ft)。

  1. 将卡箍 (7) 置于弯头连接 (9) 和涡轮增压器的上方。 将卡箍上的螺母拧紧,扭矩为 14 ± 1 N·m (124 ± 9 lb ft)。 用软锤沿卡箍直径周围轻轻敲打。 拧紧螺母至扭矩为 14 ± 1 N·m (124 ± 9 lb in)。

  1. 将 O 形密封圈安装到空气管 (3) 上。 使用工具 (B) 润滑 O 形密封圈。 安装空气管 (3) 。



    图 2g01116759

  1. 安装油管组件 (1) 。

  1. 安装排放管组件 (2) 。

  1. 安装空气滤清器。

Caterpillar Information System:

C-10 Petroleum Engine Engine Oil Pan
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft - Remove
C15 and C18 Engines for Caterpillar Built Machines Belt Tensioner
3508B, 3512B and 3516B Generator Set Engines Turbocharger - Remove
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
C9 Marine Generator Set Fuel System Secondary Filter - Replace
3412E Petroleum Engine General Information
C15 and C18 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C15 and C18 Engines for Caterpillar Built Machines Fuel Filter Pressure Differential Switch
C-10 Petroleum Engine Exhaust Manifold
C15 and C18 Engines for Caterpillar Built Machines Camshaft - Install
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Connector Locations
Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467} Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467}
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines Diagnostic Capabilities
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines J1939 Bridge
3508C, 3512C and 3516C Marine Engines Water Temperature Regulators - Remove
3508C, 3512C and 3516C Marine Engines Water Temperature Regulators - Install
C-10 Petroleum Engine Piston Cooling Jet
349F and 352F Excavators Swing Drive Oil - Change
PL1000E Communication ECM Electrical Connector - Inspect
C-10 Petroleum Engine Housing (Front)
PL1000E Communication ECM Wiring Harness (Open Circuit) - Test
PL1000E Communication ECM Wiring Harness (Short Circuit) - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.