Cylinder Head
Show/hide table
Illustration 1 | g00897161 |
(1) Bolts (3/4 inch)
(2) Bolts (3/8 inch)
(3) Studs
Use the following procedure to tighten the cylinder head bolts:
- Apply 6V-4876 Lubricant to all bolt threads.
- Tighten bolts 1 through 20 according to the number sequence.
Torque ... 270 ± 27 N·m (200 ± 20 lb ft)
- Tighten bolts 1 through 20 according to the number sequence.
Torque ... 390 ± 10 N·m (290 ± 7 lb ft)
- Tighten bolts 1 through 20 according to the number sequence.
Torque ... 390 ± 10 N·m (290 ± 7 lb ft)
- Install the rocker arm group.
- Tighten bolts 21 through 26 according to the number sequence to the following torque.
Torque ... 270 ± 27 N·m (200 ± 20 lb ft)
- Tighten bolts 21 through 26 according to the number sequence to the following torque.
Torque ... 390 ± 10 N·m (290 ± 7 lb ft)
- Tighten bolts 21 through 26 according to the number sequence.
Torque ... 390 ± 10 N·m (290 ± 7 lb ft)
- Tighten the 3/8 inch bolts (2) .
Torque ... 43 ± 7 N·m (32 ± 5 lb ft)
- Apply 6V-4876 Lubricant to the stud threads.
- Tighten studs (3) .
Torque ... 35 ± 5 N·m (26 ± 4 lb ft)
Show/hide table
Illustration 2 | g01411756 |
(A) Dimension
- Cylinder head thickness ... 123.73 mm (4.871 inch)
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Connecting Rod
C11 and C13 Petroleum Engines Crankshaft Seals
3176C and 3196 Engines for Caterpillar Built Machines Cylinder Liner
C15 and C18 Industrial Engines Exhaust Elbow - Remove and Install
C15 and C18 Industrial Engines Turbocharger - Install - Dual Turbocharger
C15 and C18 Industrial Engines Turbocharger - Remove - Dual Turbocharger
G3408 and G3412 Engines Carburetor Control Linkage
G3408 and G3412 Engines Carburetor Control Linkage
Installation and Initial Start-Up Procedure For G3520B Industrial Engines{1000} Installation and Initial Start-Up Procedure For G3520B Industrial Engines{1000}
3412E, C30 and C32 Marine Engines Connecting Rod Bearings - Remove
G3408 and G3412 Engines Carburetor Control Linkage
2004/08/01 A New Head Gasket is Now Available as Service Replacement {1124}
G3408C and G3412C Engines Cylinder Head
3406E and 3456 Generator Set Engines Fuel System
3408C and 3412C Marine Engines Alternator and Regulator
3412E, C30 and C32 Marine Engines Crankshaft - Remove
C7 Engines for Caterpillar Built Machines Electrical System
3412E, C30 and C32 Marine Engines Crankshaft - Remove
325D and 329D Excavators Storage Box - If Equipped
3406E and 3456 Generator Set Engines Fuel System - Prime
3406E and 3456 Generator Set Engines Electric Starting System - Test
C15 Petroleum Generator Set Engines Exhaust Temperature - Test
C11 and C13 Engines for Caterpillar Built Machines Cooling System - Inspect
C15 and C18 Industrial Engines Fuel Filter Base - Remove