Neutralizer Valve (STIC Steering) - Remove and Install
拆卸步骤
开始:
- 安装转向机架锁。 请参阅拆解和组装, "转向机架锁 - 拆卸和安装"。
- 释放液压系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
注: 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
注: 在所有软管、所有软管组件、所有导线及所有管组件上作出识别标记,以便安装。 插接好所有软管组件和所有管组件。 这将有助于防止液体渗漏,并有助于防止污染物进入系统。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
- 断开软管组件 (2) 。
Show/hide table
图 1 | g01091755 |
- 拆卸管组件 (3) 。
- 断开软管组件 (5) 和 (6) 。
- 卸下 2 只螺栓 (7) 和垫圈。 拆下空档器阀 (1) 。
- 对空档器阀 (4) 重复步骤 3 和步骤 4。
安装步骤
- 安装空档器阀 (4) 。 安装螺栓和垫圈。
Show/hide table
图 2 | g01091755 |
- 安装空档器阀 (1) 。 安装两个螺栓 (7) 和垫圈。
- 连接软管组件 (5) 和 (6) 。
- 对空档器阀 (4) 重复步骤3。
- 安装管路组件 (3) 。
- 连接软管组件 (2) 。
- 向液压油箱加油至正确的油位。 请参阅操作和保养手册, "液压系统油位 – 检查"。
- 检查转向空档器阀的操作情况。 请参阅系统操作、测试和调整, "转向空档器阀 - 检查和调整"。
End By: 断开转向机架锁。 请参阅 拆解和组装, "转向机架锁 - 拆卸和安装"。
Caterpillar Information System:
R1600G Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Disassemble
R1600G Load Haul Dump Machine Systems Hydraulic Tank - Disassemble
R1300G Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Install
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Gear Pump (Steering) - Assemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Radiator Core - Clean
446D Backhoe Loader Machine Systems Bucket - Remove and Install
797 Off-Highway Truck Front Axle Breather - Replace
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector
C15 Petroleum Generator Set Engines Fuel Transfer Pump
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Gear Pump (Steering) - Disassemble
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Gear Pump (Steering) - Install
252-9310 Parking Brake Control Gp (Automatic) Custom Product Support Literature for the R1300G Load Haul Dump{1408, 4250} 252-9310 Parking Brake Control Gp (Automatic) Custom Product Support Literature for the R1300G Load Haul Dump{1408, 4250}
R1300G Load Haul Dump Machine Systems Neutralizer Valve (Implement and Steering) - Remove and Install
725 and 730 Articulated Trucks Machine Systems Steering System Troubleshooting
R1300G Load Haul Dump Machine Systems Pilot Valve (STIC Steering) - Remove
R1600G Load Haul Dump Machine Systems Hydraulic Tank - Assemble
725 and 730 Articulated Trucks Machine Systems Hoist System Troubleshooting
725 and 730 Articulated Trucks Machine Systems Piston Pump (Steering, Hoist) - Test and Adjust
725 and 730 Articulated Trucks Machine Systems Piston Pump (Brake, Hoist, Fan) - Test and Adjust
725 and 730 Articulated Trucks Machine Systems Electric Drive Pump (Secondary Steering) - Check
725 and 730 Articulated Trucks Machine Systems Service Brake Air - Purge
834H Wheel Dozer and 836H Landfill Compactor Axle Oil Cooler Filter - Replace - If Equipped
797B Off-Highway Truck Lifting and Tying Down the Machine
834H Wheel Dozer and 836H Landfill Compactor Axle Oscillation Bearings - Lubricate