Vane Pump (Implement, Steering, Pilot and Braking) - Remove
拆卸步骤
开始:
- 安装转向机架锁。 请参阅拆解和组装, "转向机架锁 - 拆卸和安装"。
- 释放液压系统压力。 请参阅拆解和组装, "系统压力 - 释放"。
- 拆卸空气滤清器。 请参阅拆解和组装, "空气滤清器 - 拆卸和安装"。
注: 清洁度是一项重要的因素。 拆卸步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
注: 在所有软管、所有软管组件、所有导线及所有管组件上作出识别标记,以便安装。 插接好所有软管组件和所有管组件。 这将有助于防止液体渗漏,并有助于防止污染物进入系统。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
- 将液压油箱中的油排入合适的容器以便保存或废弃这些油。 有关液压油箱的容量,请参阅操作和保养手册, "容量(再加注)"。 有关正确的排放步骤,请参阅操作和保养手册, "液压系统机油 – 更换"。
- 断开软管组件 (2) 和 (4) 。
Show/hide table
图 1 | g01091484 |
- 从接头 (5) 上断开软管组件。 拆下接头 (5) 。
- 断开管组件 (3) 。
- 拆下固定护罩 (1) 的两个螺栓。 拆下护罩 (1) 。
- 松开两个卡箍 (6) 。 拆下两颗螺栓 (7) 。
Show/hide table
图 2 | g01091483 |
- 拆卸管组件 (3) 。
- 将适当的起吊设备连接到叶轮泵 (10) 上。 叶轮泵 (10) 的重量约为 59 kg (130 lb)。
Show/hide table
图 3 | g01091737 |
- 拆下两个螺栓 (12) 。
- 拆下叶轮泵 (10) 。
- 拆下固定适配器 (8) 的四个螺栓。 拆下适配器 (8) 和 O 形密封圈。
- 拆下四个螺栓 (11) 和弯头 (9) 。
- 从弯头 (9) 上拆下 O 形密封圈。
- 拆下 O 形密封圈 (12) 。
Show/hide table
图 4 | g01091738 |
Caterpillar Information System:
C15 and C18 Industrial Engines Flywheel Housing - Remove and Install
Bench Test Procedure for a 776 and 777 Off-Highway Truck Transmission {3030, 3073} Bench Test Procedure for a 776 and 777 Off-Highway Truck Transmission {3030, 3073}
446D Backhoe Loader Machine Systems Pilot Valve (Stabilizer) - Assemble
CB-214E, CB-224E and CB-225E Vibratory Compactors Machine Systems Vibratory Valve - Disassemble
3500 Industrial Engines Auxiliary Water Pump
446D Backhoe Loader Machine Systems Pilot Valve (Stabilizer) - Disassemble
3508 EUI Engine for Off-Highway Truck/Tractors Water Pump
CB-334E Series II and CB-335E Series II Paving Compactors Tire Inflation Pressure Adjustment
797 Off-Highway Truck Engine Components - Rebuild//Replace/Install Reman - 797 LAA Machines Only
797 Off-Highway Truck Engine Components - Clean/Inspect, Rebuild/Install Reman, Install New - 797 LAA Machines Only
C4.4 (Mech) Industrial Engine Battery or Battery Cable - Disconnect
C4.4 (Mech) Industrial Engine Battery - Replace
R2900G Load Haul Dump Machine Systems Diverter Valve (Secondary Steering) - Install
252-9310 Parking Brake Control Gp (Automatic) Custom Product Support Literature for the R1300G Load Haul Dump{1408, 4250} 252-9310 Parking Brake Control Gp (Automatic) Custom Product Support Literature for the R1300G Load Haul Dump{1408, 4250}
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Gear Pump (Steering) - Install
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Gear Pump (Steering) - Disassemble
C15 Petroleum Generator Set Engines Fuel Transfer Pump
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector
797 Off-Highway Truck Front Axle Breather - Replace
446D Backhoe Loader Machine Systems Bucket - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Radiator Core - Clean
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Gear Pump (Steering) - Assemble
R1300G Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Install
R1600G Load Haul Dump Machine Systems Hydraulic Tank - Disassemble