Flywheel Housing - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7574 | 连杆支架 | 2 |
开始:
- 拆下曲轴后密封。 请参阅拆解和组装 , "曲轴后密封 - 拆卸"。
- 拆下电起动马达。 请参阅拆解和组装 , "电起动马达 - 拆卸和安装" 。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 卸下将发动机油底壳固定在飞轮壳体 ( 2) 上的螺栓 (1)。
Show/hide table
图 2 g01058428 - 将工具 (A) 和适当的起吊设备安装在飞轮壳体 ( 2) 上。 飞轮壳 (2) 的重量约为
105 kg (230 lb) 。 - 拆下螺栓 (3)。 将飞轮壳从缸体上拆下。
- 将密封垫 (4) 从飞轮壳上拆下。
Show/hide table
图 1 | g01008304 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7574 | 连杆支架 | 2 |
B | 8T-9022 | 硅胶密封垫 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 彻底清理飞轮壳和缸体的后端面。
Show/hide table
图 3 g01058428 - 将工具 (A) 和适当的起吊设备安装在飞轮壳体 ( 2) 上。 飞轮壳 (2) 的重量约为
105 kg (230 lb) 。 - 将密封垫 (4) 安装到缸体的定位销上。 在密封垫的底部涂敷工具 ( B),填充缸体、飞轮壳体与发动机油底壳的空隙。
- 定位飞轮壳 (2) 后安装螺栓 ( 3)。
Show/hide table
图 4 g00551652 - 按照下列步骤拧紧螺栓:
- 按照数字顺序依次将螺栓 1 到螺栓 24 上紧到
40 ± 10 N·m (30 ± 7 lb ft) 的扭矩。 - 按照数字顺序重新依次将螺栓 1 到螺栓 9 上紧到
135 ± 20 N·m (100 ± 15 lb ft) 的扭矩。 - 按照数字顺序重新依次将螺栓 10 到螺栓 24 上紧到
55 ± 10 N·m (40 ± 7 lb ft) 的扭矩。
Show/hide table图 5 g01008304 - 按照数字顺序依次将螺栓 1 到螺栓 24 上紧到
- 安装将发动机油底壳固定在飞轮壳体 ( 2) 上的螺栓 (1)。
- 拆下工具 (A)。
结束:
- 安装电起动马达。 请参阅拆解和组装 , "电起动马达 - 拆卸和安装" 。
- 安装曲轴后密封。 请参阅拆解和组装 , "曲轴后油封 - 安装"。
Caterpillar Information System:
G3500 Engines Cooling System Coolant (NGEC) - Change
3500 Industrial Engines Auxiliary Water Pump
C7 Marine Engines Engine Sensors - Remove and Install
C7 Marine Engines Fuel Cooler - Remove and Install
C4.4 (Mech) Industrial Engine Battery or Battery Cable - Disconnect
C4.4 (Mech) Industrial Engine Battery - Replace
3126E Truck Engines Reference Material
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Oil Filter (Transmission)
G3406 Engines Cylinder Head Valves
G3500B Engines Engine Oil Lines
C15 and C18 Industrial Engines Engine Oil Pan - Remove and Install
G3520B Industrial Engine Oxygen Sensor Signal
XQ125 Generator Set Driven Equipment - Check
C15 Petroleum Generator Set Engines Fuel Transfer Pump
C3.3 Industrial Engine Engine Air Cleaner Element (Single Element) - Inspect/Replace
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector
C18 Generator set and C18 Marine Engines Flywheel - Remove
C18 Generator set and C18 Marine Engines Flywheel - Install
G3500 Engines Starting the Engine
C15 and C18 Industrial Engines Camshaft - Install
C15 and C18 Industrial Engines Camshaft - Remove
C13, C15, and C18 Generator Set Engines Speed Control (Switch) - Test
G3500 Generator Sets Cooling System Coolant (NGEC) - Change
C15 and C18 Industrial Engines Alternator - Remove and Install