Vibratory Valve - Disassemble
Disassembly Procedure
Start By:
- Remove the vibratory valve. Refer to Disassembly and Assembly, "Vibratory Valve - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
- Remove counterbalance valve (1) from valve body (2) .
Show/hide table
Illustration 1 | g01091372 |
- Remove O-ring seals (3), (4), and (5). Remove backup rings (6), (7), and (8) .
Show/hide table
Illustration 2 | g01091374 |
- Remove the nut and O-ring seal (9). Remove solenoid (10) .
Show/hide table
Illustration 3 | g01091378 |
- Repeat Step 3 for solenoid (11) .
- Remove valves (12) and (13) .
Show/hide table
Illustration 4 | g01091376 |
- Remove O-ring seals (15), (16), and (17). Remove backup ring (14) .
Show/hide table
Illustration 5 | g01091377 |
- Remove caps (18) and (19) .
Show/hide table
Illustration 6 | g01091420 |
- Remove relief valves (20) and (21) .
- Remove O-ring seals (22) and (24). Remove backup ring (23) .
Show/hide table
Illustration 7 | g01091444 |
Caterpillar Information System:
3500 Industrial Engines Auxiliary Water Pump
446D Backhoe Loader Machine Systems Pilot Valve (Stabilizer) - Disassemble
3508 EUI Engine for Off-Highway Truck/Tractors Water Pump
CB-334E Series II and CB-335E Series II Paving Compactors Tire Inflation Pressure Adjustment
797 Off-Highway Truck Engine Components - Rebuild//Replace/Install Reman - 797 LAA Machines Only
797 Off-Highway Truck Engine Components - Clean/Inspect, Rebuild/Install Reman, Install New - 797 LAA Machines Only
C4.4 (Mech) Industrial Engine Battery or Battery Cable - Disconnect
C4.4 (Mech) Industrial Engine Battery - Replace
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Calibration Error Code List (Caterpillar Monitoring System)
446D Backhoe Loader Machine Systems Pilot Valve (Stabilizer) - Install
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Operator Platform - Remove and Install
2004/08/02 Correction to Disassembly and Assembly , "Piston Pump (Brake) - Assemble" {4268, 5070}
446D Backhoe Loader Machine Systems Pilot Valve (Stabilizer) - Assemble
Bench Test Procedure for a 776 and 777 Off-Highway Truck Transmission {3030, 3073} Bench Test Procedure for a 776 and 777 Off-Highway Truck Transmission {3030, 3073}
C15 and C18 Industrial Engines Flywheel Housing - Remove and Install
R1300G Load Haul Dump Machine Systems Vane Pump (Implement, Steering, Pilot and Braking) - Remove
R2900G Load Haul Dump Machine Systems Diverter Valve (Secondary Steering) - Install
252-9310 Parking Brake Control Gp (Automatic) Custom Product Support Literature for the R1300G Load Haul Dump{1408, 4250} 252-9310 Parking Brake Control Gp (Automatic) Custom Product Support Literature for the R1300G Load Haul Dump{1408, 4250}
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Gear Pump (Steering) - Install
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Gear Pump (Steering) - Disassemble
C15 Petroleum Generator Set Engines Fuel Transfer Pump
C13, C15, and C18 Tier 4 Final Engines Electronic Unit Injector
797 Off-Highway Truck Front Axle Breather - Replace
446D Backhoe Loader Machine Systems Bucket - Remove and Install