Actuator Bypass Valve (Variable) - Install
安装步骤
- 将轮齿 (9) 和弹簧销 (8) 安装到阀组件 (5) 的轴上。
Show/hide table
图 1 | g02161253 |
- 插入弹簧销,直到弹簧销与轮齿外径平齐。
注: 外径为 4.7 mm (0.185 in) 的钻头可用于对齐轮齿孔与轴孔。
Show/hide table
图 2 | g02112537 |
安装在轮齿和轴内的弹簧销的视图。 |
- 将弹簧 (10) 的一端装入弹簧销。
Show/hide table
图 3 | g02161293 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将轭 (11) 安装到弹簧 (10) 的另一端。 以顺时针方向转动轭 (11) ,这样便可以将轭 11 安装到轮齿 (9) 上。 旋转靠近弹簧。
Show/hide table
图 4 | g02161300 |
- 将第二个弹簧 (10) 安装到轭 (11) 的另一端。
Show/hide table
图 5 | g02161584 |
- 将适配器 (12) 安装到弹簧 (10) 的另一端。 以顺时针方向旋转适配器,这样便可以将适配器 (12) 安装在轭 (11) 上。 旋转靠近弹簧。
- 将新组装的阀组件 (5) 安装到支架 (7) 上。 将螺栓上紧到 41 N·m (30 lb ft) 的扭矩。
Show/hide table
图 6 | g02161586 |
- 以顺时针方向旋转执行器的轴,直到停止为止。
- 通过将适配器安装在接头 (4) 内,将新组装的阀组件 (5) 和支架 (7) 安装到执行器组件 (2) 上。
注: 确保阀组件的箭头指向气流方向。
Show/hide table
图 7 | g02161587 |
- 重新安装现有的安装坚固件,穿过执行器组件和支架。 拧紧固定螺母的螺栓 (6) 至扭矩为 45 N·m (33 lb ft)。
Show/hide table
图 8 | g02161591 |
- 确保执行器抵着闭合止动块。 以顺时针方向旋转执行器的轴。
- 确保螺栓 (13) 朝向进气端,阀组件上的箭头与气流方向一致。
Show/hide table
图 9 | g02161623 |
- 确保阀组件 (5) 中的板与气流方向垂直。
Show/hide table
图 10 | g02161624 |
- 拧紧螺钉 (3) 至扭矩为 15 N·m (11 lb ft),同时固定阀组件中的板,使其与气流方向垂直。
Show/hide table
图 11 | g02161625 |
- 安装卡箍组件 (1) 。
注: 安装前,请确认执行器旁通阀在正确方向上。
Show/hide table
图 12 | g02161078 |
- 接通气体供给。
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Actuator Bypass Valve (Variable) - Remove
G3520C and G3520E Generator Set Engines Fuel Control Valve - Remove and Install
2004/05/01 UPS Flywheel Bearing Serviceability {7551}
C27 and C32 Engines for Caterpillar Built Machines Turbocharger
G3520C and G3520E Generator Set Engines Throttle Control Valve - Install
G3520C and G3520E Generator Set Engines Throttle Control Valve - Remove
Generator Set Start Module (AC Input) Safety Signs and Labels
Generator Set Start Module (AC Input) Product Drawings - Internal Schematic
Generator Set Start Module (AC Input) Product Drawings - Interconnection Diagram
Generator Set Start Module (AC Input) Electrical Connections
Generator Set Start Module (AC Input) Mounting
Generator Set Start Module (AC Input) Site Preparation
Generator Set Start Module (AC Input) Acronyms
Generator Set Start Module (AC Input) Symbols
3406E, C-10 and C-12 On-highway Engines Engine Speed/Timing Sensor Circuit - Test
Generator Set Start Module (AC Input) Model View Illustrations
Generator Set Start Module (AC Input) Troubleshooting
3176C and 3196 Engines for Caterpillar Built Machines Flywheel
2004/08/01 The Oil Level Gauge (Dipstick) has been Improved {1326}
C-9 Engine for the 330C Excavator and for the 330C Mobile Hydraulic Power Unit Engine Misfires, Runs Rough or Is Unstable
3406E and 3456 Generator Set Engines Flywheel Housing
C11 and C13 Petroleum Engines Engine Support (Front)
12M Motor Grader Centershift Cylinder Socket - Check/Adjust/Replace
C15 and C18 Industrial Engines Flywheel Housing