Flywheel - Install
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 138-7573 | Lifting Bracket | 2 |
| B | - | Guide Stud (5/8 - 18 x 8 inch) |
2 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Raise the temperature of ring gear (3) to a maximum temperature of
316 °C (600 °F) . Install ring gear (3) on flywheel (2).Show/hide table
Illustration 2 g01065075 - Install Tooling (B) in the crankshaft.
- Install Tooling (A) on flywheel (2). Use a suitable lifting device. The weight of the flywheel is approximately
35 kg (77 lb) . Position flywheel (2) on the crankshaft. - Apply clean engine oil to the threads of bolts (1).
- Install bolts (1). Remove Tooling (B). Install bolts (1) in place of Tooling (B).
- Tighten bolts (1) to a torque of
272 ± 27 N·m (200 ± 20 lb ft) . - Remove Tooling (A) from the flywheel.
- Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Show/hide table
| |
| Illustration 1 | g01065146 |
Note: Ring gear (3) must be installed with the chamfered side of the teeth upward. The chamfered side of the gear teeth will be facing toward the starting motor when the flywheel is installed. This will ensure that the starting motor will engage correctly.
End By:
- Install the flywheel adapter. Refer to Disassembly and Assembly, "Flywheel Adapter - Remove and Install".
Caterpillar Information System:
C15 Petroleum Engines Flywheel - Remove
C-15 Petroleum Engine Cooling System - Check - Overheating
G3520C and G3520E Generator Set Engines Auxiliary Water Pump - Assemble
G3520C and G3520E Generator Set Engines Auxiliary Water Pump - Disassemble
G3516B Engines MID 036 - CID 1719 - FMI 04 Generator Output Power Sensor short to ground
G3516B Engines MID 036 - CID 1719 - FMI 03 Generator Output Power Sensor open/short to +batt
3406E, C-10 and C-12 On-highway Engines Check Engine Lamp Circuit - Test
3406E, C-10 and C-12 On-highway Engines Engine Shutdown Output Circuit - Test
2005/04/01 New Injectors and New Flash Files are Now in Production. {1290, 7620}
C15 Petroleum Engines Electronic Control Module - Remove and Install
2004/04/12 Product Information Guide, SEBF1015, "Improving Component Durability" , "Final Drives and Differentials" is now available {3258, 3282, 4050}
3406E, C-10 and C-12 On-highway Engines Engine Running Output Circuit - Test
C18 Industrial Engines Plate Locations and Film Locations
C15 and C18 Industrial Engines Flywheel Adapter - Remove and Install
3126B Marine Engines Analog Sensor Supply Circuit - Test
C-15 Petroleum Engine Vibration Damper - Check
C18 Generator Set Safety Messages
3406E and 3456 Generator Set Engines Analog Sensor Supply Circuit - Test
3406E and 3456 Generator Set Engines CAT Data Link Circuit - Test
2004/05/01 Procedure to Allow Clearance to Install an Eaton VCTplus Clutch {1156}
G3520C and G3520E Generator Set Engines Generator Output Power Readings Do Not Match
3406E and 3456 Generator Set Engines Digital Sensor Supply Circuit - Test
3126B Petroleum Engine Intermittent Engine Shutdown
C15 Petroleum Engines Engine Oil Pump - Remove