Auxiliary Water Pump - Disassemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0510 | 冲头总成 | 1 |
B | - | 1 in X 4 in 钢板 | 2 |
C | 248-3311 | 固定夹具 | 1 |
D | 248-3310 | 锁紧螺母扳手 | 1 |
E | 8H-0663 | 轴承拉拔器总成 | 1 |
开始:
- 拆卸辅助水泵。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 从轴承壳体 (3) 上拆下螺塞 (1) 和螺塞 (2)。 从壳体 (5) 拆下螺塞 (6)。 从塞上卸下 O 形密封圈。
- 从轴承壳体 (3) 上拆下水泵滤清器 (4)。
Show/hide table
图 2 g01035264 - 拆下螺栓 (7) 和垫圈。 从壳体 (5) 拆下轴承壳体 ( 3)。 从轴承壳体 (3) 拆下 O 形密封圈 (8)。
Show/hide table
图 3 g01035285 - 将工具 (B) 安装到叶轮 (9) 下面。 用适当的压具和工具 (A) 拆卸叶轮。
注: 从泵轴拆卸叶轮时,应防止轴承壳体 (3) 落到地面上。
Show/hide table图 4 g03375323 - 拆下内六角头螺栓 (10)。 从轴承壳体 (3) 上拆下挡圈 (11) 和泵轴 (12)。
- 将密封组件 (13) 从轴承壳体 (3) 上拆下。
Show/hide table
图 5 g03375550 - 将泵轴 (12) 安装到工具 (C) 中。 松开调整螺钉 (14)。 用工具 (D) 将轴承锁紧螺母 (15) 从泵轴上拆下。
注: 标记泵轴花键端以显示泵轴上的右牙螺纹或左牙螺纹。
Show/hide table图 6 g03375563 - 用工具 (E) 从泵轴 (12) 上拆下轴承组件 (16)。
Show/hide table
图 7 g03375583 - 将唇形密封 (17) 从轴承壳体 (3) 上拆下。
Show/hide table
图 1 | g01036014 |
Caterpillar Information System:
G3516B Engines MID 036 - CID 1719 - FMI 04 Generator Output Power Sensor short to ground
G3516B Engines MID 036 - CID 1719 - FMI 03 Generator Output Power Sensor open/short to +batt
3406E, C-10 and C-12 On-highway Engines Check Engine Lamp Circuit - Test
3406E, C-10 and C-12 On-highway Engines Engine Shutdown Output Circuit - Test
2005/04/01 New Injectors and New Flash Files are Now in Production. {1290, 7620}
C15 Petroleum Engines Electronic Control Module - Remove and Install
2004/04/12 Product Information Guide, SEBF1015, "Improving Component Durability" , "Final Drives and Differentials" is now available {3258, 3282, 4050}
3406E, C-10 and C-12 On-highway Engines Engine Running Output Circuit - Test
Product Link - PL102C System Components
3406E, C-10 and C-12 On-highway Engines Auxiliary Brake Circuit - Test
C9 Urban Transit Bus Engine Turbocharger - Inspect
3406E and 3456 Generator Set Engines Intermittent Engine Shutdown
G3520C and G3520E Generator Set Engines Auxiliary Water Pump - Assemble
C-15 Petroleum Engine Cooling System - Check - Overheating
C15 Petroleum Engines Flywheel - Remove
C15 Petroleum Engines Flywheel - Install
C18 Industrial Engines Plate Locations and Film Locations
C15 and C18 Industrial Engines Flywheel Adapter - Remove and Install
3126B Marine Engines Analog Sensor Supply Circuit - Test
C-15 Petroleum Engine Vibration Damper - Check
C18 Generator Set Safety Messages
3406E and 3456 Generator Set Engines Analog Sensor Supply Circuit - Test
3406E and 3456 Generator Set Engines CAT Data Link Circuit - Test
2004/05/01 Procedure to Allow Clearance to Install an Eaton VCTplus Clutch {1156}