992G Wheel Loader and 854G Wheel Dozer Power Train Caterpillar


General Information

Usage:

854G 1JW
The diagnostics for a system's ECM can be accessed through the Vital Information Management System or the Caterpillar Electronic Technician (ET). Troubleshooting a system requires additional information from the machine's Service Manual. The additional manuals that may be required are the Service Manual, RENR6318, "Vital Information Management System (VIMS)", Service Manual, SENR6059, "Vital Information Management System (VIMS)", the Electrical System Schematic, the Parts Manual and the Operation and Maintenance Manual for the machine that is being serviced.

As a reference, a simplified system schematic is included at the end of this manual. For an accurate representation of the machine that is being diagnosed, refer to Electrical System Schematic in the Service Manual for the machine that is being serviced.

When the troubleshooting procedure instructs you to "REPAIR THE HARNESS OR REPLACE THE HARNESS", use the Electrical System Schematic for the machine that is being serviced to trace the circuit. Perform continuity checks at the harness connectors in order to locate harness failures. At the connectors of the components, always check the ground circuit. There must be less than five ohms of resistance between any system ground and the frame ground. Excessive ground resistance that is greater than five ohms can cause incorrect diagnosing of problems.

During troubleshooting, inspect all connections before any component is replaced. If these connections are not clean and tight, permanent electrical problems or intermittent electrical problems can result. Check that the wires are pushed into the connectors completely. Make sure that the connections are tight before other tests are made.

If wire insulation is punctured during troubleshooting, repair the damage. Seal the damaged wires with 8T-0065 RTV Silicone Sealant. Cover the sealant with two layers of 1P-0810 Tape .

Failure of an electrical component can cause the failure of other components. Also, failure of an electrical component can be caused by the failure of other components. Always attempt to correct the cause of an electrical system failure before you replace a component.

When you are removing the machine harness from any ECM, use the single screw in the center of the harness connector.

Caterpillar Information System:

950G Series II Wheel Loader Safety
966G II and 972G II Wheel Loaders Aggregate Autodig - If Equipped
2004/03/22 An Unknown Diagnostic Fault Code is Displayed on the CAT Electronic Service Tool Display {1901}
980H Wheel Loader Cooling System Coolant Sample (Level 2) - Obtain
980H Wheel Loader Cooling System Coolant Sample (Level 1) - Obtain
992G Wheel Loader Automatic Lubrication System Components - Check
120H and 135H Motor Graders Air System and Brakes Check Valve (Air Tank)
854G Wheel Dozer Capacities (Refill)
3408E and 3412E Engines for Caterpillar Built Machines CID 0164 FMI 04 Injector Actuation Pressure voltage low
854G Wheel Dozer Equipment Lowering with Engine Stopped
992G Wheel Loader and 854G Wheel Dozer Power Train Backup Alarm Always Off
D6N Track-Type Tractor Machine Systems Pilot Control Valve - Remove
545 Wheel Skidder Machine Systems Hydraulic Rotator - Assemble - Continuous Rotator Grapple
992G Wheel Loader and 854G Wheel Dozer Power Train MID 081 - CID 0041 - FMI 04
980H Wheel Loader Diagnostic Lines (Remote Pressure Taps) - If Equipped
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Loader Frame and Rear Frame - Separate
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Loader Frame and Rear Frame - Connect
992G Wheel Loader Plate Locations and Film Locations
D6N Track-Type Tractor Machine Systems Pilot Control Valve - Install
980H Wheel Loader Transmission Oil Filter - Replace
2004/04/12 Internal Changes Improve the Nitrogen Retention of the Accumulators {5077}
980H Wheel Loader Transmission Oil Sample - Obtain
AD30 Underground Articulated Truck Braking System Brake Disc Wear - Check
AD30 and AD55 Underground Articulated Trucks Power Train Electronic Control System Speed Sensor (Transmission Output) - Replace
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.