Electrohydraulic System Oil Filter - Change
Show/hide table
图 1 | g00792302 |
(1) 滤清器
(2) 目测表 (3) 加注口盖 |
- 用 1U-8760 链子扳手拆下滤清器 (1)。
- 清洁滤清器安装基座的密封表面。 确保所有旧滤清器垫片都已清除干净。
Show/hide table
图 2 g00103713 典型滤清器安装基座与垫片 注: 有关使用正确的机油,请参考本操作和保养手册, "加注容量和建议"专题(保养部分)。
- 在新的滤清器垫片上涂抹清洁的液压油。
- 用手安装滤清器。 旋拧滤清器直到滤清器垫圈接触基座。 根据滤清器上的说明拧紧滤清器。 不要过分拧紧滤清器。
- 起动发动机。 检查目测表 (2)内的油位。 机油油位应介于油箱上的"加(ADD)"和"满(FULL)"标记之间。 如果需要,拆下油加注口盖 (4)。 将正确的机油加入机油加注口。 清洁机油加注口盖。 安装机油加注口盖。
Caterpillar Information System:
C18 Generator set and C18 Marine Engines Fuel Manifold - Install
C18 Generator set and C18 Marine Engines Fuel Manifold - Remove
G3600 Engines Electrohydraulic System Oil - Change
3126B Marine Engines Engine Speed/Timing Sensor Circuit - Test
Installation Procedure for the New Drive Gears for the 3456 Engine{1206} Installation Procedure for the New Drive Gears for the 3456 Engine{1206}
C18 Generator set and C18 Marine Engines Turbocharger - Assemble
C18 Generator set and C18 Marine Engines Turbocharger - Disassemble
2004/05/31 Hose Kit Helps the Technician Properly Prepare Hydraulic Hose for Assembly {0684}
C-15 Petroleum Engine Fan Drive Bearing - Lubricate
C15 Petroleum Generator Set Engines Engine Oil Filter Base
2004/02/01 A Modification to the Air Inlet Cover Will Prevent the False Activation of a Diagnostic Event Code {1057, 1087, 5479}
2007/08/01 A New Joint Design is Introduced for the HEUI Fuel System's High Pressure Oil Pump {1307, 1714}
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Parallel Cabinet Interface
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - AC Interface Board
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - DC Interface Board
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Flywheel Interface Board
C7 Marine Engine Air Inlet and Exhaust System - Inspect
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Static Switch Interface Board
G3600 Engines Engine Oil - Change
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - User Interface Board
3126B Marine Engines Engine Temperature Sensor Open or Short Circuit - Test
3126B Marine Engines Injector Solenoid Circuit - Test
C-10 Petroleum Engine Engine Oil Cooler
3126B Petroleum Engine Fuel Transfer Pump