Turbocharger - Assemble
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Compressor housing must go straight on the turbocharger assembly without tilting. Tilting may cause compressor blade to tip, or the compressor shaft can be damaged. |
- Put an alignment mark on the new turbocharger cartridge in the same location as the old turbocharger cartridge.
Show/hide table
Illustration 1 g01051449 - Align the marks and connect compressor housing (1) to turbocharger cartridge (3). Install clamp assembly (2) and tighten to a torque of
14 ± 1 N·m (10 ± 1 lb ft) . Tap the clamp assembly lightly with a hammer. Tighten the clamp again to a torque of14 ± 1 N·m (10 ± 1 lb ft) . - Rotate the turbocharger cartridge in order to ensure that the turbocharger cartridge does not contact the compressor housing.
- Align the marks and connect turbine housing (5) onto turbocharger cartridge (3). Install clamp assembly (4) and tighten to a torque of
14 ± 1 N·m (10 ± 1 lb ft) . Tap the clamp assembly lightly with a hammer. Tighten the clamp again to a torque of14 ± 1 N·m (10 ± 1 lb ft) . - Rotate the turbocharger cartridge in order to ensure that the turbocharger cartridge does not contact the turbine housing.
End By:
- Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Caterpillar Information System:
C18 Generator set and C18 Marine Engines Turbocharger - Disassemble
2004/05/31 Hose Kit Helps the Technician Properly Prepare Hydraulic Hose for Assembly {0684}
C-15 Petroleum Engine Fan Drive Bearing - Lubricate
C15 Petroleum Generator Set Engines Engine Oil Filter Base
2004/02/01 A Modification to the Air Inlet Cover Will Prevent the False Activation of a Diagnostic Event Code {1057, 1087, 5479}
2007/08/01 A New Joint Design is Introduced for the HEUI Fuel System's High Pressure Oil Pump {1307, 1714}
2004/02/01 A New Joint Design is Introduced for the HEUI Fuel System's High Pressure Oil Pump {1714}
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Current - Calibrate - AC Current
2004/03/29 Cat Service Tools Releases New Hose Cutting Machine {0678, 0684}
C13, C15, and C18 Generator Set Engines Air Inlet and Exhaust System
3612 and 3616 Fast Vessel Engines Cooling System Coolant (DEAC) - Change
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Voltage - Calibrate - AC Voltage
Installation Procedure for the New Drive Gears for the 3456 Engine{1206} Installation Procedure for the New Drive Gears for the 3456 Engine{1206}
3126B Marine Engines Engine Speed/Timing Sensor Circuit - Test
G3600 Engines Electrohydraulic System Oil - Change
C18 Generator set and C18 Marine Engines Fuel Manifold - Remove
C18 Generator set and C18 Marine Engines Fuel Manifold - Install
G3612 and G3616 Engines Electrohydraulic System Oil Filter - Change
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Parallel Cabinet Interface
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - AC Interface Board
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - DC Interface Board
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Flywheel Interface Board
C7 Marine Engine Air Inlet and Exhaust System - Inspect
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Static Switch Interface Board