Turbocharger - Disassemble
Start By:
- Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Do not attempt to disassemble the turbocharger cartridge assembly. The turbocharger cartridge assembly is not field serviced, and should be replaced only as a unit. |
Show/hide table
Illustration 1 | g01051449 |
- Position the turbocharger on a bench. Place alignment marks on compressor housing (1), turbocharger cartridge (3), and turbine housing (5).
- Loosen the nut on clamp assembly (4). Separate turbine housing (5) from turbocharger cartridge (3).
- Loosen the nut on clamp assembly (2). Separate turbocharger cartridge (3) from compressor housing (1).
Caterpillar Information System:
2004/05/31 Hose Kit Helps the Technician Properly Prepare Hydraulic Hose for Assembly {0684}
C-15 Petroleum Engine Fan Drive Bearing - Lubricate
C15 Petroleum Generator Set Engines Engine Oil Filter Base
2004/02/01 A Modification to the Air Inlet Cover Will Prevent the False Activation of a Diagnostic Event Code {1057, 1087, 5479}
2007/08/01 A New Joint Design is Introduced for the HEUI Fuel System's High Pressure Oil Pump {1307, 1714}
2004/02/01 A New Joint Design is Introduced for the HEUI Fuel System's High Pressure Oil Pump {1714}
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Current - Calibrate - AC Current
2004/03/29 Cat Service Tools Releases New Hose Cutting Machine {0678, 0684}
C13, C15, and C18 Generator Set Engines Air Inlet and Exhaust System
3612 and 3616 Fast Vessel Engines Cooling System Coolant (DEAC) - Change
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Voltage - Calibrate - AC Voltage
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Voltage - Calibrate - DC Bus Voltage
C18 Generator set and C18 Marine Engines Turbocharger - Assemble
Installation Procedure for the New Drive Gears for the 3456 Engine{1206} Installation Procedure for the New Drive Gears for the 3456 Engine{1206}
3126B Marine Engines Engine Speed/Timing Sensor Circuit - Test
G3600 Engines Electrohydraulic System Oil - Change
C18 Generator set and C18 Marine Engines Fuel Manifold - Remove
C18 Generator set and C18 Marine Engines Fuel Manifold - Install
G3612 and G3616 Engines Electrohydraulic System Oil Filter - Change
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Parallel Cabinet Interface
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - AC Interface Board
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - DC Interface Board
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Interface Board - Remove and Install - Flywheel Interface Board
C7 Marine Engine Air Inlet and Exhaust System - Inspect