Gear Pump (Steering) - Assemble
Assembly Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 9U-5717 | Shrink Tubing | 1 |
Note: Cleanliness is an important factor. Before you begin assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform the assembly procedures on a clean work surface. Keep components covered and protected at all times.
- Install lip seal (20) in end cover (12), if the lip seal was previously removed.
Show/hide table
 | |
| Illustration 1 | g01043666 |
- Install seal (19) and backup seal (18) in end cover (12) .
Show/hide table
 | |
| Illustration 2 | g01043662 |
- Install O-ring seal (17) in end cover (12) .
Show/hide table
 | |
| Illustration 3 | g01043660 |
- Install bushing (16) in end cover (12). Install Tooling (A) on the threaded end of drive gear (6) and install the drive gear in end cover (12) .
Show/hide table
 | |
| Illustration 4 | g01043658 |
- Install driven gear (14) and bushing (15) in steering pump housing (13) .
Show/hide table
 | |
| Illustration 5 | g01043642 |
- Install steering pump housing (13) in end cover (12) .
Show/hide table
 | |
| Illustration 6 | g01043640 |
- Install seal (11) and backup seal (10) in end cover (8) .
Show/hide table
 | |
| Illustration 7 | g01043639 |
- Install O-ring seal (9) in end cover (8) .
Show/hide table
 | |
| Illustration 8 | g01043638 |
- Position end cover (8) and install bolts (7). Tighten bolts (7) to a torque of 45 to 55 N·m (33 to 41 lb ft).
Show/hide table
 | |
| Illustration 9 | g01043637 |
- Install shaft key (5) in gear drive (6). Install Tooling (A) on the threaded portion of the shaft.
Show/hide table
 | |
| Illustration 10 | g01043636 |
- Position gear (4). Install the washer and nut (3) .
Show/hide table
 | |
| Illustration 11 | g01043635 |
- Install O-ring seal (2) in steering pump assembly (1) .
End By: Install the steering pump. Disassembly and Assembly, "Gear Pump (Steering) - Install".
Caterpillar Information System:
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Gear Pump (Steering) - Disassemble
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Gear Pump (Steering) - Remove
CP-323C and CS-323C Paving Compactors Cooling System Coolant (ELC) - Change
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarrier Hydraulic System Relief Valve (Line) - Test and Adjust
C15 On-Highway Engine Engine Oil Pump - Assemble
C15 On-Highway Engine Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
CP-323C and CS-323C Paving Compactors Circuit Breakers - Reset
CP-323C and CS-323C Paving Compactors Battery or Battery Cable - Inspect/Replace
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Gear Pump (Steering) - Install
2004/02/16 Lighting Group Uses New Seals and Bolt-On Covers {1429, 1434}
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
446D Backhoe Loader Engine Crankcase Breather - Clean
2004/02/16 Correction to Testing and Adjusting , "Piston Pump Neutral - Test and Adjust" {5070}
446D Backhoe Loader Engine Air Precleaner - Clean
446D Backhoe Loader Engine Oil Level - Check
Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553} Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553}
CB-214E, CB-224E and CB-225E Paving Compactors Isolation Mounts - Inspect
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Metering Pump (Steering) - Remove and Install
446D Backhoe Loader Axle Oscillation Bearings - Lubricate
C15 and C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install