Gear Pump (Steering) - Disassemble
Disassembly Procedure
Start By:
- Remove the steering pump. Refer to Disassembly and Assembly, "Gear Pump (Steering) - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform the disassembly procedures on a clean work surface. Keep components covered and protected at all times.
- Remove O-ring seal (2) from steering pump assembly (1) .
Show/hide table
 | |
| Illustration 1 | g01043635 |
- Remove nut (3) and the washer. Remove gear (4) .
- Remove shaft key (5) from gear drive (6) .
Show/hide table
 | |
| Illustration 2 | g01043636 |
- Remove bolts (7) and remove end cover (8) .
Show/hide table
 | |
| Illustration 3 | g01043637 |
- Remove O-ring seal (9) from end cover (8) .
Show/hide table
 | |
| Illustration 4 | g01043638 |
- Remove backup seal (10) and seal (11) from end cover (8) .
Show/hide table
 | |
| Illustration 5 | g01043639 |
- Remove steering pump housing (13) from end cover (12) .
Show/hide table
 | |
| Illustration 6 | g01043640 |
- Remove bushing (15) and driven gear (14) from steering pump housing (13) .
Show/hide table
 | |
| Illustration 7 | g01043642 |
- Remove drive gear (6) and bushing (16) from end cover (12) .
Show/hide table
 | |
| Illustration 8 | g01043658 |
- Remove O-ring seal (17) from end cover (12) .
Show/hide table
 | |
| Illustration 9 | g01043660 |
- Remove backup seal (18) and seal (19) from end cover (12) .
Show/hide table
 | |
| Illustration 10 | g01043662 |
- If necessary, remove lip seal (20) from end cover (12) .
Show/hide table
 | |
| Illustration 11 | g01043666 |
Caterpillar Information System:
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Gear Pump (Steering) - Remove
CP-323C and CS-323C Paving Compactors Cooling System Coolant (ELC) - Change
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarrier Hydraulic System Relief Valve (Line) - Test and Adjust
C15 On-Highway Engine Engine Oil Pump - Assemble
C15 On-Highway Engine Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
CP-323C and CS-323C Paving Compactors Circuit Breakers - Reset
CP-323C and CS-323C Paving Compactors Battery or Battery Cable - Inspect/Replace
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
CP-323C and CS-323C Paving Compactors Battery - Clean/Check
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Gear Pump (Steering) - Assemble
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Gear Pump (Steering) - Install
2004/02/16 Lighting Group Uses New Seals and Bolt-On Covers {1429, 1434}
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
446D Backhoe Loader Engine Crankcase Breather - Clean
2004/02/16 Correction to Testing and Adjusting , "Piston Pump Neutral - Test and Adjust" {5070}
446D Backhoe Loader Engine Air Precleaner - Clean
446D Backhoe Loader Engine Oil Level - Check
Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553} Conversion of High Flow Work Tools For Operation on High Flow Skid Steer Loaders and Multi Terrain Loaders{1408, 5057, 7553}
CB-214E, CB-224E and CB-225E Paving Compactors Isolation Mounts - Inspect
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Metering Pump (Steering) - Remove and Install
446D Backhoe Loader Axle Oscillation Bearings - Lubricate