Fuel Ratio Control
Show/hide table
Illustration 1 | g01022400 |
(1) 6N-0515 Spring
- Length under test force ... 46.00 mm (1.811 inch)
- Test force ... 30 ± 2 N (6.7 ± 0.4 lb)
- Free length after test ... 74.9 mm (2.95 inch)
- Outside diameter ... 20.57 mm (0.810 inch)
- Color code ... one yellow stripe
- Test force ... 30 ± 2 N (6.7 ± 0.4 lb)
(1) 7N-0209 Spring
- Length under test force ... 32.258 mm (1.2700 inch)
- Test force ... 88 ± 8 N (19.8 ± 1.8 lb)
- Free length after test ... 37.8 mm (1.49 inch)
- Outside diameter ... 45.42 mm (1.788 inch)
- Color code ... two yellow stripes
- Test force ... 88 ± 8 N (19.8 ± 1.8 lb)
Note: To test the spring rate, preload the spring to 16 N (3.6 lb). Compress the spring for another 10 mm (0.4 inch) and check the load that is on the spring at this point. The load should be 173.6 ± 11.0 N (39.03 ± 2.47 lb).
(1) 6N-0513 Spring
- Length under test force ... 13.97 mm (0.550 inch)
- Test force ... 120 ± 9 N (27.0 ± 2.0 lb)
- Free length after test ... 31.0 mm (1.22 inch)
- Outside diameter ... 32.537 mm (1.2810 inch)
- Color code ... one yellow stripe
- Test force ... 120 ± 9 N (27.0 ± 2.0 lb)
Note: To test the spring rate, preload the spring to 50 N (11.2 lb). Compress the spring for another 10 mm (0.4 inch) and check the load that is on the spring at this point. The load should be 120 ± 5 N (27.0 ± 1.1 lb).
(1) 9N-1754 Spring
- Length under test force ... 12.0 mm (0.47 inch)
- Test force ... 6.22 ± 0.44 N (1.398 ± 0.099 lb)
- Free length after test ... 17.5 mm (0.69 inch)
- Outside diameter ... 4.57 mm (0.180 inch)
- Test force ... 6.22 ± 0.44 N (1.398 ± 0.099 lb)
Caterpillar Information System:
Required Tooling for Bench Testing Hydraulic Components {0784, 4000, 4005, 4129, 4250, 4300, 5050} Required Tooling for Bench Testing Hydraulic Components {0784, 4000, 4005, 4129, 4250, 4300, 5050}
C27 and C32 Engines for Caterpillar Built Machines CID 0168 FMI 02 System Voltage intermittent/erratic
C11 and C13 Engines for Caterpillar Built Machines CID 0168 FMI 01 System Voltage Low
C27 and C32 Engines for Caterpillar Built Machines CID 0274 FMI 04 Atmospheric Pressure short to ground
C27 and C32 Engines for Caterpillar Built Machines CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
Oil Renewal System Introduction
3408C, 3412C and 3412D High Performance Marine Engines Gear Group (Front)
G3520B Engines Engine Misfires, Runs Rough or Is Unstable
2003/10/01 A New Integral Seal Provides Improved Sealing for Aluminum Oil Pans {1302}
G3520B Engines Location of Components
120H and 135H Motor Graders Power Train Wheel Spindle - Remove
Cat Commercial Diesel Engine Fluids Recommendations Engine Oil for Precombustion Chamber (PC) Diesel Engines - Engine Crankcase Fluid Recommendations for All 3500 Series and Smaller PC Diesel Engines
120H and 135H Motor Graders Machine Systems Tie Rod (Steering) - Remove and Install
3408C, 3412C and 3412D High Performance Marine Engines Fuel Injection Pump Housing
3500B and 3500B High Displacement Generator Set Engines General Information
2003/09/15 Install the Engine Oil Filter Properly {1308}
797F and 797F XQ Off-Highway Truck Hydraulic Fan System Pressure Reducing Valve (Hydraulic Fan)
3612 and 3616 Fast Vessel Engines Plate Locations and Film Locations
3500B and 3500B High Displacement Generator Set Engines Pistons, Rings and Connecting Rods - One-Piece Piston
G3500B Engines Ignition Timing - Adjust
G3406 Engines Gas Pressure Regulator
C11 and C13 Engines for Caterpillar Built Machines Event Codes
C15 On-highway Engine Variable Valve Actuator Oil Pressure Sensor - Remove and Install
C15 On-highway Engine Variable Valve Actuator Oil Pressure Solenoid - Remove and Install