C15 and C18 Engines for Caterpillar Built Machines Caterpillar


Electric Starting Motor - Remove and Install

Usage:

826K 232

拆卸步骤


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。


------ WARNING! ------

发动机的意外起动会对在设备上工作的人员造成伤害或死亡。


  1. 断开蓄电池。

  2. 在与电起动马达和电磁阀相连的所有线束上做出索引标记。


    图 1g01100842

  3. 从电磁阀 (1) 上断开线束组件。

  4. 断开线束组件 (2)。

  5. 将适当的起吊设备固定在电起动马达 (3) 上。 电起动马达的重量约为 26 kg (57 lb)

  6. 卸下螺栓 (4)。 将电起动马达 (3) 和密封垫 (5) 从飞轮壳上拆下。

安装步骤


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。




    图 2g01100842

  1. 将适当的起吊设备固定在电起动马达 (3) 上。 电起动马达的重量约为 26 kg (57 lb)

  2. 将电起动马达 (3) 和密封垫 (5) 定位到飞轮壳上。 安装螺栓 (4)。 将起吊设备从电起动马达上拆下。

  3. 将线束组件定位到电起动马达上后安装螺母 (2)。 拧紧螺母至扭矩为 31 ± 4 N·m (23 ± 3 lb ft)


    图 3g01100656

  4. 将线束组件定位到电磁阀上后安装螺母 (8)。 拧紧螺母至扭矩为 31 ± 4 N·m (23 ± 3 lb ft)

  5. 将线束组件定位到电磁阀上后安装螺母 (8)。 拧紧螺母至扭矩为 2.25 ± 0.25 N·m (20 ± 2 lb in)

  6. 将线束组件定位到电磁阀上后安装螺母 (7)。 拧紧螺母至扭矩为 2.25 ± 0.25 N·m (20 ± 2 lb in)

  7. 如有必要,安装接头,然后安装螺母 (10) 和螺栓 (9)。 将螺母和螺栓上紧到 31 ± 4 N·m (23 ± 3 lb ft) 的扭矩。

  8. 连接蓄电池。

Caterpillar Information System:

C15 On-highway Engine Alternator - Remove and Install
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Related Options
2003/12/01 New Cylinder Head Groups and Valve Mechanisms {1100, 1102, 1121, 1123}
2014/07/30 New Cylinder Head Groups and Valve Mechanisms {1100, 1102, 1121, 1123}
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Acronyms
C27 and C32 Engines for Caterpillar Built Machines CID 0261 FMI 13 Engine Timing Calibration required
C27 and C32 Engines for Caterpillar Built Machines CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C27 and C32 Engines for Caterpillar Built Machines CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C27 and C32 Engines for Caterpillar Built Machines CID 0172 FMI 04 Intake Manifold Air Temp short to ground
C27 and C32 Engines for Caterpillar Built Machines CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
C27 and C32 Engines for Caterpillar Built Machines CID 0342 FMI 08 Secondary Engine Speed signal abnormal
C15 On-highway Engine Flywheel - Install
C15 and C18 Engines for Caterpillar Built Machines Vibration Damper
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Troubleshooting
2003/11/01 Improved O-Ring Seals for Fuel Injectors for Longer Seal Life {1254}
2003/10/01 Improved O-Ring Seals for Fuel Injectors for Longer Seal Life {1254}
C15 and C18 Engines for Caterpillar Built Machines Fan Drive
C15 and C18 Engines for Caterpillar Built Machines Alternator Mounting
G3500B Engines Crankshaft - 20 Cylinders
G3500B Engines Electronic Control System Parameters
C15 On-highway Engine Refrigerant Compressor Mounting Group - Remove and Install
C15 On-highway Engine Alternator Mounting Group - Remove and Install
C15 On-highway Engine Belt Tensioner - Remove and Install
G3520C and G3520E Generator Set Engines Electric Starting System
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.