Circuit Breaker Harness Assembly {1420} Caterpillar


Circuit Breaker Harness Assembly {1420}

Usage:

769C 01X
Articulated Truck
All
Asphalt Paver
All
Backhoe Loader
All
Cold Planer
All
Compact Wheel Loader
All
Earthmoving Compactor
All
Electric Power Generation
All
Engine
All Gas Engines
Excavator
All
Forest Products
All
Integrated Toolcarrier
All
Landfill Compactor
All
Load Haul Dump
All
Machine Engines
All
Mini Hydraulic Excavator
All
Motor Grader
All
Off-Highway Truck/Tractor
All
Paving Compactor
All
Pipelayer
All
Road Reclaimer/Soil Stabilizer
All
Skid Steer Loader
All
Soil Compactor
All
Telehandler
All
Track-Type Loader
All
Track-Type Skidder
All
Track-Type Tractor
All
Truck Engines
All
Underground Articulated Truck
All
Wheel Dozer
All
Wheel Loader
All

Introduction

In order to ensure reliable operation of the circuit breakers (1), ensure that the harness assembly is properly secured to the circuit breakers (1). Loose connections can be the result of performing either of the following two actions:

  • Assembling the mounting hardware in the incorrect location

  • Applying the incorrect torque to the mounting hardware

An internal tooth star washer (5) that is located between the wire terminal (2) and the circuit breaker (1) provides the maximum torque retention for the connection.

Proper Assembly Technique

  • When an internal tooth star washer (5) is supplied with the circuit breaker (1), ensure that the star washer is placed between the wire terminal (2) and the circuit breaker (1).

  • When a flat washer (4) is supplied with the circuit breaker (1), ensure that the flat washer (4) is located between the wire terminal (2) and the screw (6).

  • Tighten the joint to the torque value that is recommended in Table 1. Table 1 shows some typical sizes for studs and screws that are found throughout the line of Caterpillar circuit breakers.

  • Reinstall fasteners in the original location.

  • Ensure that the harness is adequately secured

  • For the correct order of assembly for the hardware and the harness, refer to Illustrations 1 through 4.

Table 1
Typical Sizes for Studs and Screws 
Type  Thread Size  Torque(1)  Tolerance 
Stud  1/4-28  6 N·m (4.43 lb ft)  +/- 1 N·m (0.74 lb ft) 
Stud  3/8-24  9 N·m (6.64 lb ft)  +/- 1 N·m (0.74 lb ft) 
Stud  10-32  2.25 N·m (1.66 lb ft)  +/- .25 N·m (0.18 lb ft) 
Screw  8-32  1.7 N·m (1.25 lb ft)  +/- .20 N·m (0.15 lb ft) 
(1) For accurate torque settings, use the 6V-4980 Torque Screwdriver Tool Group.


Illustration 1g03158416
Breaker with stud


Illustration 2g03159696
Breaker with drawing of screw
(1) Circuit breaker
(2) Wire terminal
(3) Nut
(4) Flat washer
(5) Lockwasher ( Internal tooth star washer)


Illustration 3g03158418
Breaker with screw terminals


Illustration 4g03159697
Breaker with screw
(1) Circuit breaker
(2) Wire terminal
(4) Flat washer
(5) Lockwasher (Internal tooth star washer)
(6) Screw

Caterpillar Information System:

3406E, C-10, C-12, C-15, C-16 Truck Engines Refill Capacities and Recommendations
C15 On-highway Engine Inlet and Exhaust Valve Springs - Remove and Install
C15 and C18 Generator Set Engines Cylinder Liner - Remove
C15 and C18 Generator Set Engines Cylinder Liner - Install
3126E and 3126B Commercial and Truck Engines Engine Oil and Filter - Change
2003/12/01 SOLAS Requirements for Fuel Lines {1274}
C11 and C13 Engines Diverter Valve (Coolant) - Remove
C11 and C13 Engines Engine Oil Cooler - Remove
C11 and C13 Engines Crankshaft - Install
C15 On-highway Engine Inlet and Exhaust Valve Guides - Remove and Install
C15 On-highway Engine Inlet and Exhaust Valves - Remove and Install
C15 On-highway Engine Inlet and Exhaust Valve Seat Inserts - Remove and Install
G3500B Engines Compressor Bypass - Check
2003/08/01 New Hose Improves the Drainage of Oil from the Turbocharger During a Continuous Prelube Cycle {1052}
3046 Engine for Caterpillar Built Machines Belt Tension Chart
3044C Industrial Engine and Engines for Caterpillar Built Machines Alternator and Regulator
3044C Industrial Engine and Engines for Caterpillar Built Machines Electric Starting Motor
C11 and C13 Engines Air Compressor Drive Gear - Remove and Install
C27 and C32 Generator Set Engines Camshaft Bearings - Remove
C27 and C32 Generator Set Engines Camshaft Bearings - Install
C11 and C13 Engines Diverter Valve (Coolant) - Install
2003/08/01 Diagnosis of Failure of Exhaust Valve {1105}
G3406 Engines Camshaft
C11 and C13 Engines Precooler - Remove
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.