Crankshaft - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7574     | 连杆支架     | 2     |
B     | 8T-5096     | 千分表总成     | 1     |
C     | 4C-5590     | 防粘结剂     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将曲轴主轴承的上半部分放在缸体中。 将曲轴主轴承的下半部分放在曲轴主轴承盖中。
Show/hide table
注意 |
---|
确保曲轴主轴承锁片与缸体和曲轴主轴承盖中的槽相互啮合。 |
- 将工具 (A) 和适当的起吊设备连接到曲轴 (6) 上。 曲轴 (6) 的重量约为 129 kg (285 lb)。 将曲轴主轴承上半部分和曲轴 (6) 安置在缸体内。
Show/hide table
图 1 | g01013519 |
- 安装曲轴止推轴承 (3) 。
- 安装曲轴主轴承下半部分 (5) 。
- 安置曲轴主轴承盖 (4) 时,使零件号朝向缸体右侧。 按原数字顺序依次安置曲轴主轴承盖 (4) 。
注: 安装曲轴主轴盖 (4) 时,应使零件号朝向发动机右侧。 可通过位于底面上压印的数字 1 到 7 确认数字顺序。 止推板仅用于 4 号曲轴主轴承上。
- 将清洁的 "SAE 30W" 机油或含钼润滑脂涂抹在螺栓螺纹和垫圈上。 安装螺栓。 拧紧螺栓至扭矩为 50 ± 5 N·m (37 ± 4 lb ft)。 在每个螺栓头上标上标记。 将螺栓再转动 90 ± 5度(1/4圈)。
注: 安装轴承盖 (4) 时使用新的螺栓。
- 利用工具 (B) 检查曲轴的轴向间隙。 轴向间隙必须为 0.10 至 0.50 mm (0.004 至 0.020 in)。
- 安装连杆轴承 (1) 和连杆盖 (2) 。
注: 断裂的连杆需要小心处理。 连杆和连杆盖的断裂表面不应放置在任意表面上。 连杆和连杆盖应该侧立放置,以避免损坏。 如有可能,应将连杆和连杆盖用螺栓固定在一起,以避免损坏。
- 将工具 (C) 涂抹在连杆盖螺栓上。 安装连杆盖螺栓。 拧紧连杆盖螺栓至扭矩为 130 ± 7 N·m (95 ± 5 lb ft)。
- 在每个螺栓头上标上标记。 将每根螺栓再拧紧 60 ± 5 度(1/6圈)。
End By:
- 安装飞轮壳体。 请参阅 拆解和组装, "飞轮壳体 - 拆卸和安装"。
- 安装前壳体。 请参阅 拆解和组装, "壳体(前) - 安装"。
- 安装发动机油底壳。 请参阅 拆解和组装, "发动机油底壳 - 拆卸和安装"。
Caterpillar Information System:
C15 On-highway Engine Inlet and Exhaust Valve Guides - Remove and Install
C15 On-highway Engine Inlet and Exhaust Valves - Remove and Install
C15 On-highway Engine Inlet and Exhaust Valve Seat Inserts - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Crankshaft - Remove
SPP101 Skid Mounted Pumper Engine Crankcase Breather - Clean
2003/08/01 A Previous High Temperature Locknut is Used in Engine Exhaust System Groups {7553}
G3406 Engines Ignition Transformer
SPP101 Skid Mounted Pumper Model View Illustrations
C3.3 Industrial Engine Cylinder Block - Inspect
3500B and 3500C Marine Engines Engine Governing - Adjust
G3520B Engines Engine Overcrank
SPP101 Skid Mounted Pumper Maintenance Interval Schedule
C11 and C13 Engines Engine Oil Cooler - Remove
C11 and C13 Engines Diverter Valve (Coolant) - Remove
2003/12/01 SOLAS Requirements for Fuel Lines {1274}
3126E and 3126B Commercial and Truck Engines Engine Oil and Filter - Change
C15 and C18 Generator Set Engines Cylinder Liner - Install
C15 and C18 Generator Set Engines Cylinder Liner - Remove
C15 On-highway Engine Inlet and Exhaust Valve Springs - Remove and Install
3406E, C-10, C-12, C-15, C-16 Truck Engines Refill Capacities and Recommendations
Circuit Breaker Harness Assembly {1420} Circuit Breaker Harness Assembly {1420}
G3500B Engines Compressor Bypass - Check
2003/08/01 New Hose Improves the Drainage of Oil from the Turbocharger During a Continuous Prelube Cycle {1052}
3046 Engine for Caterpillar Built Machines Belt Tension Chart