Inlet and Exhaust Valve Guides - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A(1) | 9U-6895 | Valve Guide Driver | 1 |
Show/hide table
(1) | Part of 9U-7530 Engine Tool Group |
Start By:
- Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove valve stem seal (1) from valve guide (2).
- Use Tooling (A) and a hammer to remove the valve guide from the cylinder head.
Show/hide table
Illustration 1 | g01003942 |
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A(1) | 9U-6895 | Valve Guide Driver | 1 |
B(1) | 9U-6894 | Guide Collar | 1 |
Show/hide table
(1) | Part of 9U-7530 Engine Tool Group |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Illustration 2 | g01003943 |
- Lubricate the bores for the valve guides with clean engine oil.
- Install valve guide (2) in the cylinder head with Tooling (A) and Tooling (B), as shown.
Note: Tooling (B) must be used in order to install the valve guide to the correct height.
Height to top of valve guide from cylinder head surface ...
35.00 ± 0.50 mm (1.378 ± 0.020 inch) Note: For more information, refer to Specifications, "Cylinder Head Valves".
- Install valve stem seal (1) on the valve guide.
End By:
- Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".
Caterpillar Information System:
C15 On-highway Engine Inlet and Exhaust Valves - Remove and Install
C15 On-highway Engine Inlet and Exhaust Valve Seat Inserts - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Crankshaft - Remove
SPP101 Skid Mounted Pumper Engine Crankcase Breather - Clean
2003/08/01 A Previous High Temperature Locknut is Used in Engine Exhaust System Groups {7553}
G3406 Engines Ignition Transformer
SPP101 Skid Mounted Pumper Model View Illustrations
C3.3 Industrial Engine Cylinder Block - Inspect
3500B and 3500C Marine Engines Engine Governing - Adjust
G3520B Engines Engine Overcrank
SPP101 Skid Mounted Pumper Maintenance Interval Schedule
G3406 Engines Water Temperature Regulator
C11 and C13 Engines Crankshaft - Install
C11 and C13 Engines Engine Oil Cooler - Remove
C11 and C13 Engines Diverter Valve (Coolant) - Remove
2003/12/01 SOLAS Requirements for Fuel Lines {1274}
3126E and 3126B Commercial and Truck Engines Engine Oil and Filter - Change
C15 and C18 Generator Set Engines Cylinder Liner - Install
C15 and C18 Generator Set Engines Cylinder Liner - Remove
C15 On-highway Engine Inlet and Exhaust Valve Springs - Remove and Install
3406E, C-10, C-12, C-15, C-16 Truck Engines Refill Capacities and Recommendations
Circuit Breaker Harness Assembly {1420} Circuit Breaker Harness Assembly {1420}
G3500B Engines Compressor Bypass - Check
2003/08/01 New Hose Improves the Drainage of Oil from the Turbocharger During a Continuous Prelube Cycle {1052}