2003/09/15 Caterpillar


An Improved Alternator Belt is Used {1357}

Usage:

793B 1HL
Caterpillar Products: Machine Engines
  • All 3500 Series
  • Service Magazine, SEPD0700, 15 September 2003, "An Improved Alternator Belt is Used". Disregard this article. The value for belt tension should be given in units of force. Refer to the following article.

    Description of Change: An new alternator belt is being introduced for use in all 3500 Machine Engines. The new alternator belt is constructed of a material that has a proven resistance to fatigue. The new alternator belt also has a higher temperature rating.

    Adaptable To: The 141-7116 Belt is a direct replacement for the 7E-4841 Serpentine Belt, which is being discontinued in August 2003. The 141-7116 Belt is currently used on 992G Wheel Loaders. In August 2003, the new alternator belt will be used on all of the above products. The new alternator belt has the same dimensions as the previous alternator belt.

    Belt Tension is Critical to the Service Life of Alternator Belts

    To obtain the maximum service life of the alternator belt and of the pulleys, the correct belt tension is critical. If the tension is inadequate, the belt may roll on the pulley or the belt may slip. The slipping will reduce the service life of the belt. If the tension is excessive, the extra tension on the belt and on the pulleys will reduce the service life of the parts.

    Tension for the 141-7116 Belt

    Tension for a new belt ... 800 N (180 lb)
    Tension for a used belt ... 489 N (110 lb)

    When you install a new belt, adjust the belt to the correct tension. Then, operate the engine for a minimum of 30 minutes at the full load rpm (rated speed) that is stamped on the engine information plate.

    A belt is considered to be used after at least 30 minutes of use at the rated speed. After a minimum of 30 minutes of operation at the rated speed, stop the engine and adjust the tension to the specification for a used belt.

    The new 240-8220 Belt Tension Gauge Gp is recommended for tensioning of the belt.

    A New Belt Tension Gauge is Available

    The new 240-8220 Belt Tension Gauge Gp is now available. The gauge is for use with belts that have eight ribs. The gauge will work with belts that have a top width in the range of 9.65 to 31.75 mm (0.380 to 1.250 inch). The gauge has a working range of 445 to 890 N (100 to 200 lb).

    Caterpillar Information System:

    2003/08/04 The Nameplate Is Now Bolted to the Grill {7251, 7557}
    M325D MH Material Handler Window Washer Reservoir - Fill
    120H and 135H Motor Graders Machine Systems Piston Pump (Hydraulic and Steering) - Install
    120H and 135H Motor Graders Machine Systems Piston Pump (Hydraulic and Steering) - Remove
    R1600G Load Haul Dump Brake Release - If Equipped
    R1600G Load Haul Dump Ride Control Accumulator - Check - If Equipped
    Load Haul Dump Braking System Relief Valve (Brake Accumulator)
    R1600G Load Haul Dump Hydraulic System Oil Level - Check
    769D Off-Highway Truck and 771D Quarry Truck Operation Information
    2003/10/20 New Supports for the Fender Are Available {7252}
    CP-533E and CS-533E Vibratory Soil Compactors Propel System Electrical Schematic
    769D Off-Highway Truck and 771D Quarry Truck Operator Controls
    2003/10/01 An Improved Alternator Belt is Used {1357}
    CP-533E and CS-533E Vibratory Soil Compactors Hydraulic Tank Breather - Replace
    AP-655C and BG-2255C Asphalt Pavers Machine Systems Gear Pump (Vibratory) - Disassemble
    AP-655C and BG-2255C Asphalt Pavers Machine Systems Gear Pump (Vibratory) - Assemble
    143H and 163H Motor Graders Machine Systems Sideshift Cylinder - Remove and Install
    Machine Security System (MSS) Integrated Configuration
    773E Off-Highway Truck Operation Information
    AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Conveyor) - Disassemble
    AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Conveyor) - Assemble
    Custom Product Support Literature for the Hydraulic Adjustment Procedure for the Long Reach Front on 320C L, 322C L, 325C L and 330C L Excavators{5050, 5117, 5456, 5458} Custom Product Support Literature for the Hydraulic Adjustment Procedure for the Long Reach Front on 320C L, 322C L, 325C L and 330C L Excavators{5050, 5117, 5456, 5458}
    Load Haul Dump Braking System Foot Brake Control
    R1300G Load Haul Dump Machine Electrical System Circuit Breaker
    Back to top
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.