Camshaft Gear - Remove and Install
开始:
- 拆下前盖。 请参阅拆解和组装, "前盖 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在拆卸凸轮轴齿轮时,不要转动曲轴或凸轮轴。 如果在安装时没有正确调整前齿轮总成的正时,活塞与气门之间将会发生干涉,进而导致发动机损坏。 |
- 将 1 号活塞安置在压缩冲程的上止点。 请参阅测试和调整, "找到 1 号活塞上止点位置"。
- 确认凸轮轴齿轮 (1) 与前壳体 (3) 上的正时标记 (X) 对准。
- 拆下螺栓 (2),然后拆下凸轮轴齿轮 (1)。
Show/hide table
图 1 | g01010536 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在拆卸凸轮轴齿轮时,不要转动曲轴或凸轮轴。 如果在安装时没有正确调整前齿轮总成的正时,活塞与气门之间将会发生干涉,进而导致发动机损坏。 |
- 将凸轮轴齿轮 (1) 背面的孔与适配器中的定位销对准。 安装凸轮轴齿轮 (1)。
注: 凸轮轴正时至关重要。 当 1 号活塞位于压缩冲程的上止点时,凸轮轴齿轮上的正时标记必须与前盖上的正时标记对准。 请参阅测试与调整, "齿轮总成(前)- 正时"。
- 确认凸轮轴齿轮 (1) 与前壳体 (3) 上的正时标记 (X) 对准。
注: 如果定时标记没有对准,则拆下凸轮轴齿轮 (1) 并旋转凸轮轴,直到定时标记对准。
- 安装螺栓 (2)。
Show/hide table
图 3 g02725378 凸轮轴齿轮的数字紧固顺序。 在初始顺序后再次拧紧螺栓 (1) 和 (4)。 - 按图 3 中所示的数字顺序拧紧凸轮轴齿轮的螺栓。 拧紧至扭矩为
240 ± 40 N·m (180 ± 30 lb ft) 。 再次将螺栓 (1) 和 (4) 拧紧至扭矩为240 ± 40 N·m (180 ± 30 lb ft) 。 - 检查凸轮轴齿轮与可调节惰轮齿轮之间的齿隙。 此齿隙应为
0.3556 ± 0.254 mm (0.014 ± 0.010 in) 。 参考测试和调整, "齿轮总成(前)- 正时",以了解齿隙调整步骤。
Show/hide table
图 2 | g01010536 |
结束:
- 安装前盖。 请参阅拆解和组装, "前盖 - 安装"。
Caterpillar Information System:
C11 and C13 Engines Valve Mechanism Cover Base - Remove and Install
C15 and C18 Petroleum Generator Sets Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C11 and C13 Engines Water Pump - Install
UPS 250 and UPS 300 Uninterruptible Power Supplies System Bypass Operation
2003/07/01 Prevent Coolant Leaks Around the Precombustion Chamber {1550}
3500B Locomotive Engines Turbocharger Support
C175–16 Locomotive Engine CAN Data Link
C7 On-highway Engine Refill Capacities and Recommendations
C7 On-highway Engine Engine Oil Level Gauge - Calibrate
C15 On-highway Engine Diverter Valve (Coolant) - Remove
C15 On-highway Engine Diverter Valve (Coolant) - Install
C15 On-highway Engine Pump Drive - Remove
2003/07/21 The Oil Pan Gasket now Requires a Gasket Sealant to be Used {1302, 7555}
C15 On-highway Engine Diverter Valve (Coolant) - Assemble
C15 On-highway Engine Diverter Valve (Coolant) - Disassemble
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Generator Start-up Checklist
C13 Engine Turbocharger - Remove - High Pressure Turbocharger
C13 Engine Turbocharger - Install - High Pressure Turbocharger
C15 On-highway Engine Engine Control Module - Remove and Install
C15 and C18 Petroleum Generator Sets Automatic Start/Stop - Inspect
C15 On-highway Engine Compression Brake - Assemble
C15 On-highway Engine Compression Brake - Disassemble
C15 On-highway Engine Compression Brake - Remove
C15 On-highway Engine Compression Brake - Install