Electronic Unit Injector - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
B     | 9U-6862     | 锥形碳刷     | 1     |
9U-7237 | 刷子扩展工具     | 1     | |
C     | 9U-6863     | 小号孔刷     | 1     |
9U-7237 | 刷子扩展工具     | 1     | |
D     | 8T-2998     | 润滑剂     | 1     |
- 使用工具 (B) 清洁喷油器支座 (7) 。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g01009642 |
(7) 喷油器支座 (8) 顶端孔 |
- 使用工具 (C) 清洁顶端孔 (8) 。
注: 不要重复使用密封圈。 安装时使用新的密封圈。
- 用按 50/50 混合的清洁的机油和工具 (D) 稍微润滑孔。
Show/hide table
图 2 | g01009613 |
- 记录单体喷油器序列号和喷油器确认代码。 注意,在更换一个新单体喷油器时,必须把 "E-Trim"(电子校准)值编入发动机控制模块。 有关更多信息,请参见故障诊断与排除, "喷油器代码 - 校准"。
- 安装单体喷油器 (3) 和支架 (5) 。
Show/hide table
图 3 | g01009643 |
(Y) 电子喷油器代码 |
Show/hide table
注意 |
---|
当使用喷油器总成的时候,新喷油器总成的电子喷油器代码必须通过电子维修工具上的校准菜单编入发动机个性模块软件中。 如果没有输入新的燃油喷油器总成的电子编码,则假定为以前燃油喷油器总成特征。 如果不可能立刻将喷油器的电子喷油器代码重新编入到个性模块软件中,发动机不会严重受损。 不过应该尽快重新编入新电子喷油器的代码,以便能尽快达到发动机的最优性能。 |
- 安装螺栓 (4) 。 拧紧螺栓 (4) 至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。
- 将线束组件 (2) 连接到单体喷油器 (3) 上。
- 连接软管组件 (1) 。
Show/hide table
图 4 | g01009601 |
End By: 安装摇臂轴。 请参阅 拆解和组装, "摇臂轴和推杆 - 安装"。
Caterpillar Information System:
C11 and C13 Engines Electronic Unit Injector - Remove
C11, C13 and C15 On-highway Engines 0283-07 Intake Valve Actuation Oil Pressure not responding (91)
2003/07/01 Quality of Remanufactured Camshafts {1210}
C7 On-highway Engine Electronic Control Module - Remove and Install
C7 On-highway Engine Cylinder Head - Install
C7 On-highway Engine Cylinder Head - Remove
C7 On-highway Engine Turbocharger - Install
C7 Engines for Combat and Tactical Vehicles Engine Oil Level Gauge - Calibrate
C7 On-highway Engine Turbocharger - Remove
C15 and C18 Petroleum Generator Sets Parallel Operation
3512C HD SR500 Generator Sets Single Unit Operation
120H and 135H Motor Graders Machine Systems Metering Pump (Steering) - Remove and Install
C11 and C13 Engines Rocker Shaft and Pushrod - Remove
C11 and C13 Engines Rocker Shaft and Pushrod - Install
C11 and C13 Engines Fuel Filter Base - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C11 and C13 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C4.4 (Mech) Industrial Engine Electrical System
G3520C and G3520E Generator Set Engines Valve Cover - Remove and Install
2003/11/01 New Unit Injector Rocker Arm Is Now Used {1123}
2003/07/21 A New Oversized Oil Pump Idler Gear Shaft is Available for 3054, 3054B, 3056 and 3056E Engines {1234, 1304}
C7 On-highway Engines Turbocharger - Inspect
C11 and C13 Engines Water Pump - Remove
G3520C and G3520E Engines Engine Mount