Camshaft Bearings - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 6V-4077 | 凸轮轴轴承工具 | 1 |
| B | 8S-2241 | 凸轮轴轴承工具总成 | 1 |
| C | 5P-5247 | 液压拉拔器 | 1 |
| D | 8H-0684 | 棘轮扳手 | 1 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在工具 (A) 上安装凸轮轴轴承 (1) 。
注: 拆卸飞轮壳体和前壳体后，可用工具 (B) 来安装凸轮轴轴承。
Show/hide table
 | |
| 图 1 | g00578338 |
- 将凸轮轴轴承 (1) 和工具 (A) 放入孔中。
注: 凸轮轴轴承接头必须位于缸径的水平中心线的位置上。 上机油孔必须高于座孔水平中心线20 ± 5度。 凸轮轴轴承的下机油孔应该低于座孔水平中心线20 ± 5度。 凸轮轴轴承接头必须朝向缸体内部。
Show/hide table
 | |
| 图 2 | g02108639 |
从后看 (X) 凸轮轴轴承接头的位置 (Y) 机油孔的位置 | |
- 在工具 (A) 上安装工具 (C) 并将凸轮轴轴承 (1) 拖入孔中。
注: 用工具 (D) 代替工具 (C) 。
Show/hide table
 | |
| 图 3 | g00578349 |
- 安装凸轮轴轴承后，测量孔。 孔必须为 92.00 ± 0.06 mm (3.622 ± 0.002 in)。
End By: 安装凸轮轴。 请参阅 拆解和组装, "凸轮轴 - 安装"。
Caterpillar Information System:
Replacing the Convection Jacket Water Heaters with a Recirculating Jacket Water Heater on 3500 Engines{1383} Replacing the Convection Jacket Water Heaters with a Recirculating Jacket Water Heater on 3500 Engines{1383}
3508C, 3512C and 3516C Marine Engines Camshaft Bearings - Remove
G3520C and G3520E Generator Set Engines Cylinder Liner - Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Flywheel Telemetry - Calibrate
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Bypass Valve - Remove and Install
G3500 Engines MID 018 - CID 0552 - FMI 11 Engine Speed present during an O2 calibration
G3500 Engines MID 018 - CID 0551 - FMI 01 Oxygen Sensor not connected to buffer
2003/06/01 Improved Radiator for the Generator Set Engine {1353}
G3520C and G3520E Generator Set Engines Piston and Connecting Rods - Install
G3520C and G3520E Generator Set Engines Piston and Connecting Rods - Remove
G3304 and G3306 Engines Crankshaft - Install
3500 Engines Fuel Filter Housing - Install
C3.3 Industrial Engine Engine - Clean
2003/07/01 An Improved Spin-On Oil Filter Is Now Available {1306, 1308}
Installation of the 249-2439 Seal {1371} Installation of the 249-2439 Seal {1371}
C7 Engines for Combat and Tactical Vehicles Cruise Control Parameters
C7 Engines for Combat and Tactical Vehicles Smart Idle Parameters
C7 Engines for Combat and Tactical Vehicles Timer Parameters
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Vibration Sensors Zeroes - Calibrate
3406C Marine Auxiliary Generator Set Safety Messages
C7 Engines for Combat and Tactical Vehicles 0110-11 Very High Coolant Temperature (61)
C7 Engines for Combat and Tactical Vehicles 0100-11 Very Low Oil Pressure (46)
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Rotor Position Sensor - Calibrate
C7 Engines for Combat and Tactical Vehicles 0190-00 Engine Overspeed Warning (35)