G3520C and G3520E Generator Set Engines Caterpillar


Cylinder Liner - Install

Usage:

G3520C B9P

安装步骤

表 1
所需工具    
工具     零件号     零件说明     数量    
B     1U-9895     十字挡块     1    
3H-0465 压拉器板     2    
8F-6123 螺栓     2    
0S-1575 螺栓     4    
3B-1925 垫圈     4    
C     8T-0455     缸体凸出量工具组     1    
D     2P-8260     缸套安装器     1    


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。


缸套凸出量

安装缸套前,按照下列步骤测量缸套凸出量。

  1. 确保这些部件清洁、干燥:缸体上表面, 缸套的缸孔, 隔板 和 缸套。 去除隔板上表面的所有刻痕。

  1. 为隔板安装一个新密封垫并安装隔板。 请参阅拆解和组装, "缸盖- 安装"。

  1. 禁止在缸套上安装 O 形密封圈或加注口带箍。 将缸套放入缸筒。

  1. 使用工具 (B) 按照下列步骤将隔板和缸套固定到位。

    1. 在缸套周围安装 4 个螺栓和垫圈。

    1. 将缸套周围的螺栓均匀地拧紧至扭矩为 95 N·m (70 lb ft)。

    1. 安装剩余的工具 (B) 。 确保 1U-9895 横梁 6 被置于缸套的中间位置。 确保缸套表面清洁。 均匀地拧紧固定十字档块的螺栓至扭矩为 70 N·m (50 lb ft)。

    1. 测量十字档块底部到隔板顶部的距离。 缸套两侧的测量值必须相等。 如果测量值不同,再次拧紧螺栓。

  1. 使用工具 (C) 测量缸套突出量。

  1. 将千分表安装在量规体内。 使用仪表缸体后部作为千分表的归零位。

  1. 将量规体置于隔板上,让千分表的点位于缸套法兰上。 读取千分表,确定缸套凸出量。 测量缸套周围四等分点的突出量。 测量缸套外法兰的突出量。 不需测量内圈的突出量。

    缸套凸出量必须为 0.060 至 0.200 mm (0.0024 至 0.0079 in)。

    高低测量值可接受的最大值差为 0.05 mm (0.002 in)。

    注: 如果缸套周围的测量值不同,旋转缸套至缸筒内的不同位置。 如果缸套凸出量不符合规格,把该缸套移到不同的缸筒内。 检查缸体的上表面。 测量缸体上的缸套孔。 如果孔太浅,则必须返工。




    图 1g01087469

  1. 如果缸套凸出量不到 0.13 ± 0.070 mm (0.005 ± 0.0030 in),测量以下零件的厚度:

    (4) 隔板 ... 12.31 ± 0.025 mm (0.490 ± 0.0010 in)

    (5) 缸套法兰 ... 12.65 ± 0.02 mm (0.500 ± 0.0010 in)

    (6) 隔板密封垫 ... 0.21 ± 0.025 mm (0.010 ± 0.0010 in)

  1. 如果缸套凸出量正确,对齐缸套和缸体上的标记。

  1. 拆卸工具 (B) 和 (C) 。 拆卸缸套、隔板和隔板上的密封垫。

安装缸套




    图 2g01004731

  1. 在 O 形密封圈 (1) 的凹槽上和 O 形密封圈上涂抹肥皂液。 在缸套 (2) 上安装 O 形密封圈。 而且,用肥皂液涂抹缸筒。

  1. 将加注口带箍 (3) 浸泡在清洁的发动机机油中。 将 加注口带箍 (3) 立即安装到缸套 (2) 上。

  1. 在加注口带箍膨胀前立即安装缸套。 确保缸套和缸体上的标记对齐。

  1. 使用工具 (D) 将缸套压入缸体内。

End By: 安装活塞和连杆组件。 请参阅 拆解和组装, "活塞和连杆 - 安装"。

Caterpillar Information System:

UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Flywheel Telemetry - Calibrate
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Bypass Valve - Remove and Install
G3500 Engines MID 018 - CID 0552 - FMI 11 Engine Speed present during an O2 calibration
G3500 Engines MID 018 - CID 0551 - FMI 01 Oxygen Sensor not connected to buffer
2003/06/01 Improved Radiator for the Generator Set Engine {1353}
G3520C and G3520E Generator Set Engines Piston and Connecting Rods - Install
G3520C and G3520E Generator Set Engines Piston and Connecting Rods - Remove
G3304 and G3306 Engines Crankshaft - Install
3500 Engines Fuel Filter Housing - Install
3500 Engines Fuel Filter Housing - Remove
G3304 and G3306 Engines Crankshaft - Remove
3406C Marine Auxiliary Generator Set Plate Locations and Film Locations
3508C, 3512C and 3516C Marine Engines Camshaft Bearings - Remove
Replacing the Convection Jacket Water Heaters with a Recirculating Jacket Water Heater on 3500 Engines{1383} Replacing the Convection Jacket Water Heaters with a Recirculating Jacket Water Heater on 3500 Engines{1383}
3508C, 3512C and 3516C Marine Engines Camshaft Bearings - Install
C3.3 Industrial Engine Engine - Clean
2003/07/01 An Improved Spin-On Oil Filter Is Now Available {1306, 1308}
Installation of the 249-2439 Seal {1371} Installation of the 249-2439 Seal {1371}
C7 Engines for Combat and Tactical Vehicles Cruise Control Parameters
C7 Engines for Combat and Tactical Vehicles Smart Idle Parameters
C7 Engines for Combat and Tactical Vehicles Timer Parameters
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Vibration Sensors Zeroes - Calibrate
3406C Marine Auxiliary Generator Set Safety Messages
C7 Engines for Combat and Tactical Vehicles 0110-11 Very High Coolant Temperature (61)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.