Piston and Connecting Rods - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 9S-9082     | 发动机盘车工具     | 1     |
B     | 1P-1861     | 挡圈钳     | 1     |
C     | 271-0498     | 活塞环扩展器     | 1     |
H     | 1U-7616     | 活塞环压缩器     | 1     |
J     | 6V-4876     | 润滑剂     | 1     |
K     | 364-2837 (1)     | 安装工具组件     | 1     |
Show/hide table
( 1 ) | 用于 350-0074 缸套 。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (C) 将活塞环 (6) 安装在活塞 (3) 上。
Show/hide table
图 1 | g00582421 |
- 活塞机油控制环的端部应与机油环末端开口成 180 度。 从机油环末端开口处必须能看见机油环弹簧的白色部分。
- 安装中间环时让有 "UP" 标记的一侧朝向活塞顶部。 定位中间环时,让绿色条位于末端开口右侧。
- 安装顶活塞环时,让红色条位于末端开口右侧。
- 安装后,活塞环末端开口互相间约成 120 度。
- 将清洁的发动机机油涂在活塞销 (4) 、活塞销轴承和活塞销 (4) 的孔上。
Show/hide table
图 2 | g01051820 |
- 将连杆 (5) 置于活塞 (3) 中,并安装活塞销 (4) 。
- 使用工具 (B) 安装固定活塞销 (4) 的挡圈。
- 在连杆 (5) 内安装连杆轴承的上半部分。 确保轴承后面的凸台在连杆 (5) 上的轴承凸台凹槽内。
- 将清洁的发动机机油涂敷在缸套孔上。
Show/hide table
图 3 | g02340238 |
- 如有必要,将工具 (K) 安装在缸套顶部。
- 将清洁的发动机机油涂在活塞环和缸套孔上。 使用工具 (H) 压缩活塞环。
Show/hide table
图 4 | g01056335 |
Show/hide table
注意 |
---|
活塞和连杆安装不当可能会使发动机受到严重破坏。 确保连杆孔一侧的倒角与曲轴止推板面相邻。 连杆孔方形的一侧必须与同一曲轴轴径上的其他连杆相邻。 |
- 在发动机内安装活塞和连杆组件。
- 在连杆盖 (2) 上安装连杆轴轴的下半部分。 确保轴承后面的凸台位于连杆盖 (2) 上的轴承凸台凹槽内。
Show/hide table
图 5 | g00582418 |
- 检查轴承间隙。 有关正确步骤,请参阅拆解和组装, "轴承间隙 - 检查"。
- 将清洁的发动机机油涂在连杆轴瓦上半部分和下半部分。
- 将工具 (J) 涂敷到螺栓的螺纹和连杆盖 (2) 的螺纹上。
- 将连杆盖 (2) 定位于连杆上,然后将螺栓 (1) 安装在连杆盖 (2) 内。
- 拧紧螺栓 (A) 和 (B) 至扭矩为 90 ± 5 N·m (65 ± 4 lb ft)。
Show/hide table
图 6 | g01087388 |
(12) 带斜面的连杆侧 (13) 定位销 |
- 拧紧螺栓 (C) 和 (D) 至扭矩为 90 ± 5 N·m (65 ± 4 lb ft)。
- 再次拧紧螺栓 (C) 和 (D) 至扭矩为 90 ± 5 N·m (65 ± 4 lb ft)。
- 将各螺栓再额外拧紧 90 ± 5 度。
- 检查同一轴径上的两个连杆间是否存在侧隙。 间隙必须为 0.85 ± 0.332 mm (0.034 ± 0.0130 in)。
- 使用工具 (A) 转动发动机以接近连杆盖上的螺栓。
End By:
- 安装活塞冷却喷嘴。 请参阅 拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
- 安装缸盖。 请参阅 拆解和组装, "缸盖- 安装"。
Caterpillar Information System:
G3520C and G3520E Generator Set Engines Piston and Connecting Rods - Remove
G3304 and G3306 Engines Crankshaft - Install
3500 Engines Fuel Filter Housing - Install
3500 Engines Fuel Filter Housing - Remove
G3304 and G3306 Engines Crankshaft - Remove
3406C Marine Auxiliary Generator Set Plate Locations and Film Locations
G3304 and G3306 Engines Camshaft Bearings - Install
G3304 and G3306 Engines Camshaft Bearings - Remove
C11, C13 and C15 On-highway Engines 0105-04 Intake Manifold Air Temperature voltage low (38)
C11, C13 and C15 On-highway Engines 0105-03 Intake Manifold Air Temperature voltage high (38)
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
G3500 Engines MID 018 - CID 0523 - FMI 11 No A/F Ratio Engine Speed Sensor **Shutdown**
2003/06/01 Improved Radiator for the Generator Set Engine {1353}
G3500 Engines MID 018 - CID 0551 - FMI 01 Oxygen Sensor not connected to buffer
G3500 Engines MID 018 - CID 0552 - FMI 11 Engine Speed present during an O2 calibration
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Bypass Valve - Remove and Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Flywheel Telemetry - Calibrate
G3520C and G3520E Generator Set Engines Cylinder Liner - Install
3508C, 3512C and 3516C Marine Engines Camshaft Bearings - Remove
Replacing the Convection Jacket Water Heaters with a Recirculating Jacket Water Heater on 3500 Engines{1383} Replacing the Convection Jacket Water Heaters with a Recirculating Jacket Water Heater on 3500 Engines{1383}
3508C, 3512C and 3516C Marine Engines Camshaft Bearings - Install
C3.3 Industrial Engine Engine - Clean
2003/07/01 An Improved Spin-On Oil Filter Is Now Available {1306, 1308}
Installation of the 249-2439 Seal {1371} Installation of the 249-2439 Seal {1371}