Cylinder Head - Disassemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 5S-1330 | 气门弹簧压缩器 | 1 |
B | 8S-2263 | 弹簧测试仪 | 1 |
C | 359-4208 | 气门座镶圈拆卸工具 | 1 |
D | 350-7768 | 电动液压泵总成 | 1 |
E | FT-3123 | 气门导管冲头 | 1 |
F | 459-2619 | 工具组件 | 1 |
G | 5P-0944 | 定位销拉拔器总成 | 1 |
H | 4C-5592 | 防粘结剂 | - |
开始:
- 拆下缸盖。
- 从缸盖 (2) 上卸下挺柱组件 (1)。
Show/hide table
图 2 g01086847 - 从挺柱组件 (1) 上卸下挺柱导管弹簧 (3)。
Show/hide table
图 1 | g01086846 |
注: 标记挺柱组件,以便于安装。
- 安装工具 (A) 以压缩气门弹簧 (5) 和气门弹簧 (4)。
Show/hide table
图 4 g01086852 - 从阀体 (7) 上拆下护圈 (6)。
- 拆下工具 (A)。
Show/hide table
图 5 g01086854 - 从阀体 (7) 上拆下气门弹簧座组件 (9)、气门弹簧 (5)、气门弹簧 (4) 和垫圈 (8)。
Show/hide table
图 6 g01086855 - 从缸盖 (2) 上卸下阀体 (7)。
- 重复步骤 1 到步骤 5,卸下其余的气门。
Show/hide table
图 7 g00598111 - 使用工具 (B) 检查气门弹簧力。 正确的气门弹簧力,请参考技术规格, "缸盖气门"。
Show/hide table
图 3 | g01086848 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
注: 燃烧表面和气门座镶圈孔必须没有污染物和碎屑。
- 将工具 (C) 插入气门座镶圈 (10) 的孔中。
Show/hide table
图 10 g02736198 - 滑动下部滑块,将工具 (C) 锁定到位。
注: 拆卸气门座圈时,气门座圈可能会断裂。 确保清除气门座圈上的所有碎屑。
- 将工具 (D) 连接到工具 (C) 并拆下气门座镶圈 (10)。
Show/hide table
图 11 g02736518 - 提升工具 (C),使其离开缸盖 (2),并滑动下部滑块,以解锁工具 (C)。
Show/hide table
图 12 g02736560 - 滑回工具 (C) 和气门座镶圈 (10) 的夹头。 然后拆下气门座镶圈。
Show/hide table
在使用液压油缸和拉拔器双头螺栓时,务必要确保拉拔器双头螺栓的额定容量满足或超出液压油缸的额定容量。 如果拉拔器双头螺栓的额定容量没有满足或超出液压油缸的额定容量,则拉拔器双头螺栓可能会发生意外故障。 拉拔器双头螺栓的意外故障可能会导致人身伤害或死亡。 |
Show/hide table
图 8 | g02736157 |
Show/hide table
图 9 | g02736098 |
- 使用工具 (E) 和适当的压具从缸盖 (2) 上拆卸进气门导管 (11) 和排气门导管 (12)。
Show/hide table
图 13 | g02736919 |
Show/hide table
图 14 | g02740960 |
注: 不要使用锤子来拆卸气门导管。
- 使用工具 (F) 拆下适配器 (13)。
Show/hide table
图 16 g02741090 - 从适配器 (13) 上拆下 O 形密封圈 (14) 和垫圈 (15)。
Show/hide table
图 15 | g02741080 |
- 使用工具 (G) 从缸盖 (2) 上拆下定位销 (16)。
Show/hide table
图 17 | g02741297 |
Caterpillar Information System:
C1.5 and C2.2 Marine Generator Set Engines Expansion Tank - Remove and Install
3500 Engines for Caterpillar Built Generator Sets Engine Oil Filter Base
C1.5 and C2.2 Marine Generator Set Engines Water Temperature Regulator Housing - Remove and Install
3054C Industrial Engine Fuel Injection Pump - Install - Bosch EVPE
3054C Industrial Engine Fuel Injection Pump - Remove - Bosch EVPE
C1.5 and C2.2 Generator Rotor - Remove and Install
C1.5 and C2.2 Marine Generator Set Engines Water Pump - Install
G3520B Industrial Engine Throttle Actuator
C1.5 and C2.2 Marine Generator Set Engines Engine Oil Relief Valve - Remove and Install
C1.5 and C2.2 Marine Generator Set Engines Water Pump - Remove
G3304 and G3306 Engines Magneto - Disassemble
G3500 Engines Prelube Pump - Electric
G3520C and G3520E Generator Set Engines Cylinder Head - Assemble
C1.5 and C2.2 Marine Generator Set Engines Water Temperature Regulator - Remove and Install
G3500 Engines Prelube Pump - Air
C1.5 and C2.2 Generator Exciter Field - Flash
C27 and C32 Generator Set Engines CID 0100 FMI 10 Engine Oil Pressure Sensor abnormal rate of change
C27 and C32 Industrial and Petroleum Engines CID 0102 FMI 10 Boost Pressure Sensor abnormal rate of change
Product Link 151/201 Installation Examples
3500 Engines for Caterpillar Built Generator Sets Fuel Filter Base
Product Link 151/201 Spare Input Installation
Product Link 151/201 System Installation
Product Link 151/201 Setup
Product Link 151/201 Configuration