C1.5 and C2.2 Marine Generator Set Engines Caterpillar


Cylinder Head - Install

Usage:

C2.2 TAG

Installation Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.





    Illustration 1g00828137



    Illustration 2g00828396

  1. Thoroughly clean the top of cylinder block (3) and the bottom of cylinder head (2). Ensure that there is no debris in the cylinder bores.

    Note: A number at location (5) with four digits is stamped on cylinder head gasket (4) in order to ensure the correct positioning of the cylinder head gasket. This number faces the cylinder head. Make sure that cylinder head gasket (4) for cylinder head (2) is the correct thickness as the original cylinder head gasket before installation.

    Note: The correct piston height must be maintained in order to prevent damage to the pistons and the valves. Refer to Testing and Adjusting, "Piston Height - Inspect". The correct piston height must be maintained in order to ensure that the engine conforms to the exhaust emission standards.

  1. Position cylinder head gasket (4) on the dowels (6) on the top of the cylinder block (3). Do not use any gasket sealant or compound on the cylinder head gasket.

  1. Attach a suitable lifting device to cylinder head (2) .

  1. Position cylinder head (2) on cylinder block (3). Ensure that cylinder head (2) is positioned on dowels (6). Verify that cylinder head gasket (4) is positioned correctly.

  1. Lubricate cylinder head bolts (1) with clean engine oil.



    Illustration 3g00828140

  1. Install the cylinder head bolts and gradually tighten the cylinder head bolts in a numerical sequence. The numerical sequence is shown in Illustration 3. Tighten the cylinder head bolts to a torque of 101 N·m (74 lb ft).

End By:

  1. Install the oil line. Refer to Disassembly and Assembly, "Engine Oil Line - Remove and Install".
  2. Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".
  3. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection lines - Remove and Install".
  4. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
  5. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
  6. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
  7. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".

Caterpillar Information System:

C1.5 and C2.2 Marine Generator Set Engines Cylinder Head - Remove
3412C Generator Sets Starting the Engine - EMCP II and EMCP II+ (If Equipped)
3456 Generator Sets Overspeed
3456 Generator Sets Engine Shutoffs and Engine Alarms
C1.5 and C2.2 Marine Generator Set Engines Rocker Shaft and Pushrod - Install
C1.5 and C2.2 Marine Generator Set Engines Valve Mechanism Cover - Remove and Install
C1.5 and C2.2 Marine Generator Set Engines Crankshaft Pulley - Remove and Install
Installation of Fuel/Water Separator{1260, 1263} Installation of Fuel/Water Separator{1260, 1263}
3500B and 3500C Marine Propulsion Engines System Configuration Parameters
C1.5 and C2.2 Marine Generator Set Engines Flywheel Housing - Remove and Install
3406C Generator Sets Sensors and Electrical Components
C1.5 and C2.2 Generator Set Engines Fuel Injection Pump - Install
C15 and C18 Petroleum Generator Sets Generator Operation
C1.5 and C2.2 Generator Set Engines Engine Oil Pan - Remove and Install
Caterpillar On-Highway Diesel Engine Fluids Recommendations Cold Weather Lubricants
C1.5 and C2.2 Marine Generator Set Engines Pistons and Connecting Rods - Install
C1.5 and C2.2 Generator Set Engines Crankshaft Main Bearings - Remove
C1.5 and C2.2 Generator Set Engines Crankshaft - Install
Caterpillar On-Highway Diesel Engine Fluids Recommendations Coolant Recommendations
C1.5 and C2.2 Marine Generator Set Engines Coolant Temperature Switch - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Fuel Injection Nozzle - Test
C1.5 and C2.2 Marine Generator Set Engines Engine Oil Pressure Switch - Remove and Install
3046 Engine for Caterpillar Built Machines Fuel System - Prime - Distributor Pump
C1.5 and C2.2 Generator Set Engines Glow Plugs - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.