Correction to the Disassembly and Assembly , "Transmission Hydraulic Control Valve - Disassemble" {3073, 3167}
- Wheel Loader:
- 966F Series II (S/N: 1SL1-UP; 9YJ1-UP; 8BG2000-UP)
A portion of the existing information is incorrect. Replacing Step 2 and Step 3 for installation of the solenoid valve into the transmission hydraulic control valve with the following information
- Check the condition of the three O-ring seals on the cartridge (1). Replace the O-ring seals with new parts, as needed.
Show/hide table
 | |
| Illustration 1 | g00485529 |
- Install the solenoid valve to the transmission hydraulic control valve by the following steps:
- Install cartridge (1) on manifold (3). Tighten the cartridge to a torque of 50 ± 5 N·m (37 ± 4 lb ft).
- For the 3E-3748 Solenoid Valve , tighten the nut to 5.0 ± 0.5 N·m (44 ± 4 lb in). For the 147-5399 Solenoid Valve, tighten the nut to 9.0 ± 0.5 N·m (80 ± 5 lb in).
- Install electrical connector (4) to the support clip.
Repeat these two steps for installation of the remaining solenoid valves.
Caterpillar Information System:
613C Series II Wheel Tractor-Scraper Hydraulic System Vane Motor (Elevator)
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Assemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Remove
C7 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Control Valve (Service) - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Metering Pump (HMU) - Remove
2003/06/09 New Tilt Cylinder and Lines Are Now Used {5057, 5104}
Bench Test Procedure for a 928G Wheel Loader andIT28G Integrated Toolcarrier Transmission with a Splined Coupling Drive{3030, 3066, 3073} Bench Test Procedure for a 928G Wheel Loader andIT28G Integrated Toolcarrier Transmission with a Splined Coupling Drive{3030, 3066, 3073}
963C Track-Type Loader Capacities (Refill)
2003/03/31 Correction to Disassembly and Assembly , "Transmission Planetary - Assemble" {3030, 3160}
613C Series II Wheel Tractor-Scraper Hydraulic System Bowl Circuit
Installation of Direct Conversion Center Tread Idlers {4159} Installation of Direct Conversion Center Tread Idlers {4159}
953C Track-Type Loader Before Operation
613C Series II Wheel Tractor-Scraper Hydraulic System Ejector Circuit
651E and 657E Wheel Tractor-Scrapers Power train Operational Checks
613C Series II Wheel Tractor-Scraper Hydraulic System Elevator Circuit
953C Track-Type Loader Cooling System Extended Life Coolant Extender - Add
Supplemental Documentation for the Payload Control System{7494} Supplemental Documentation for the Payload Control System{7494}
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
966F Series II Wheel Loader Power Train Transmission Hydraulic Control Valve - Disassemble
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
C7 Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install