Window Wiper and Wiper Motor (Front) - Remove
Removal Procedure
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Note: Put identification marks on all wires and on all connectors for installation purposes.
- Remove the rubber mat from the cab floor.
- Remove screws (1). Tilt plate assembly (2) forward.
Show/hide table
Illustration 1 | g00984497 |
- Disconnect light bulbs (6) and harness assemblies (3), (4), and (5) .
Show/hide table
Illustration 2 | g00984501 |
- Remove plate assembly (2) .
- Remove screws (7) and (8). Tilt plate assembly (9) forward.
Show/hide table
Illustration 3 | g00984505 |
- Disconnect harness assemblies (10), (11), and (12). Disconnect light bulbs (13) .
Show/hide table
Illustration 4 | g00984509 |
- Remove plate assembly (9) .
- Remove bolts (14). Move switch box (15) aside.
Show/hide table
Illustration 5 | g00284771 |
- Remove bolts (16) that secure the air duct to the cab. Repeat this step on the opposite side of the air duct.
Show/hide table
Illustration 6 | g00284772 |
- Remove the bolt and clip (17) that secures the harness assemblies on the left side of the air duct.
Show/hide table
Illustration 7 | g00284773 |
- Disconnect harness assembly (18) from the alarm.
Show/hide table
Illustration 8 | g00284774 |
- Pull both harness assemblies through the air duct in order to remove the air duct.
Show/hide table
Illustration 9 | g00284775 |
- Remove ties (19) from the right harness assembly.
Show/hide table
Illustration 10 | g00284777 |
- Remove bolts (20) from the base of the support assembly.
Show/hide table
Illustration 11 | g00284779 |
- Remove bolts (21) from each side of the support assembly. This will allow the steering control to be tilted for later removal of the air duct.
Show/hide table
Illustration 12 | g00284780 |
Show/hide table
Illustration 13 | g00284782 |
- Tilt the steering control assembly toward the seat. Lift the air duct and tilt the air duct toward the seat so that harness clip (22) can be removed. Remove the air duct.
Show/hide table
Illustration 14 | g00284784 |
- Disconnect harness assembly (23) from wiper motor (24) .
Show/hide table
Illustration 15 | g00284786 |
- Disconnect hose (25). Open covers (26) .
Show/hide table
Illustration 16 | g00284788 |
- Remove nuts (27) and wiper arm assemblies (28) .
Show/hide table
Illustration 17 | g00284789 |
- Remove caps (29) .
Show/hide table
Illustration 18 | g00284790 |
- Support the wiper motor assembly inside the cab. Remove nut (32) and bolt (30). Remove plate (31), the gasket and the wiper motor assembly.
Show/hide table
Illustration 19 | g00284811 |
Caterpillar Information System:
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Quick Coupler - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Blower Motor (Air Conditioner, Heater) - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Blower Motor (Air Conditioner, Heater) - Remove
G3500B Engines Vibration Damper
CP-663E, CS-663E and CS-683E Vibratory Compactors Propel System Speedometer
3034 Engine for Caterpillar Built Machines Crankshaft - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Heater Coil - Install
2003/03/10 A New Dust Ejector Group for the Exhaust Prevents Loading on the Muffler {1068}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control (Joystick) - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Heater Coil - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control (Joystick) - Remove
3034 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Remove - Serrated Connecting Rod
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Alert Indicator Is Always Flashing
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Alert Indicator Never Flashes
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Quick Coupler - Install
C-9 Engine for MT735, MT745, MT755, MT765, MTC735, MTC745, MTC755, and MTC765 Agricultural Tractors Throttle Position Sensor Circuit - Test
2003/03/10 New Track Links Improve the Service Life of the Track Chain {4170}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Window Wiper and Wiper Motor (Front) - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Design
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Ride Control Accumulator - Remove and Install
A Testing Procedure for the Automatic Burner Control{5700, 6642} A Testing Procedure for the Automatic Burner Control{5700, 6642}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Pilot Valve (Joystick)
320B, 320B L and 320B N Excavators Cooling System Coolant Sample (Level 1) - Obtain
320B, 320B L and 320B N Excavators Cooling System Coolant Sample (Level 2) - Obtain