3054E Industrial Engine Caterpillar


Inlet and Exhaust Valve Springs - Remove and Install

Usage:

3054E 304

拆卸步骤

表 1
所需工具    
工具     零件号     零件描述     数量    
A     9U-6195     气门弹簧压缩器     1    
B     9U-6198     曲轴转动工具     1    

开始:

  1. 拆下摇臂轴组件。 请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。


注: 在缸盖仍安装在缸体上时,应采用下述步骤拆卸气门弹簧。 从缸体上拆下缸盖后,有关从缸盖上拆卸气门弹簧的正确步骤,请参阅拆解和组装手册, "进气门和排气门 - 拆卸和安装"。

注: 开始拆卸气门弹簧前,请参阅技术参数, "缸盖气门",了解气门弹簧的相应信息。

  1. 拆下气门上的气门锁片前,确保活塞处于上止点位置。 如果不能保证活塞处于上止点位置,可能导致气门落入缸体中。 使用下述步骤确定活塞的上止点位置。


      注意

      在气门弹簧拆卸过程中不要转动曲轴。





      图 1g00937233

      ------ WARNING! ------

      被弹簧力爆出的零件击中,会招致人员伤害。

      确保穿上所有必要的保护装备。

      遵照建议的程序,并使用所有建议的工具以释放弹簧力。


    1. 安装工具 (A) 。


      注意

      确保在四角均匀地压缩气门弹簧,否则可能会导致气门杆损坏。


    1. 压缩气门弹簧,以便打开气门。 不要充分压缩气门弹簧,以便可以从气门杆的凹槽中拆下气门锁片 (1) 。

    1. 转动曲轴,直到活塞接触到气门。

    1. 继续转动曲轴,直到气门杆处于最高点。 此时,活塞即处于上止点。 活塞处于上止点后,释放工具 (A) 上的压力。

  1. 使用工具 (A) 压缩气门弹簧 (3) 。 拆下气门锁片 (1) 。

  1. 小心地释放工具 (A) 上的压力。 拆下气门弹簧挡圈 (2) ,然后拆下气门弹簧 (3) 。

    注: 如果需要更换所有气门弹簧,则可以同时在两个气缸上完成这一步骤。 可以在气缸 1 和气缸 4,以及气缸 2 和气缸 3 上完成这一步骤。


注意

在气门弹簧拆卸过程中不要转动曲轴。


安装步骤

表 2
所需工具    
工具     零件号     零件描述     数量    
A     9U-6195     气门弹簧压缩器     1    
B     9U-6198     曲轴转动工具     1    


注意

保持所有零件清洁无杂质。

杂质会造成快速磨损和缩短部件寿命。





    图 2g00937233

    ------ WARNING! ------

    弹簧压缩零件如果安装不当,会伤害人体。

    为避免伤害,遵照出版的装配程序,并穿上保护装备。


  1. 将新气门弹簧安置到位。

  1. 安装气门弹簧挡圈 (2) 。


    注意

    确保在四角均匀地压缩气门弹簧,否则可能会导致气门杆损坏。


  1. 安装工具 (A) 。 压缩气门弹簧 (3) 。

  1. 安装气门锁片 (1) 。

  1. 小心地释放工具 (A) 上的压力。 拆下工具 (A) 。 转动曲轴大约 45 度,以便降下活塞。 用软锤敲击气门顶部,以确保气门锁片安装正确。

    注: 如果需要更换所有气门弹簧,则可以同时在两个气缸上完成这一步骤。 可以在气缸 1 和气缸 4,以及气缸 2 和气缸 3 上完成这一步骤。

End By: 安装摇臂轴组件。 请参阅 拆解和组装, "摇臂轴和推杆 - 安装"。

Caterpillar Information System:

C1.5 and C2.2 Generator Sets Stopping the Engine
C1.5 and C2.2 Generator Sets Engine Warm-up
G3500 A3 Engines ECM Output Circuit (Prelubrication Oil Pump)
G3500 A3 Engines Engine Pre-Lube Pressure (Low)
C1.5 and C2.2 Engines for Caterpillar Built Marine Generator Sets Exhaust Manifold
C9 Marine Engines System Configuration Parameters
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Air Inlet and Exhaust System - Inspect
3056E Industrial Engine Belt Tension Chart
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Charging System - Test
2003/02/03 Checking the Motor Rotation after Replacing the Blower Motor Can Increase Service Life {7304, 7320}
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Cylinder Head - Inspect
C13 Engines for Caterpillar Built Machines Compression Brake
3054E Industrial Engine Inlet and Exhaust Valves - Remove and Install
C13 Engine for Combat and Tactical Vehicles Cooling System
3054E Industrial Engine Inlet and Exhaust Valve Guides - Remove and Install
3044C Industrial Engine Fuel and the Effect from Cold Weather
3054E Industrial Engine Water Temperature Regulator - Remove and Install
G3600 Engines Gas Engine Ignition - Bio-Gas Fuel
C1.5 and C2.2 Generator Sets Auxiliary Water Pump (Rubber Impeller) - Inspect
G3606 and G3608 Engines Gas Engine Ignition - Bio-Gas Fuel
322B L and 325B L Excavators, 322B and 325B Forest Machines and 325B Material Handler Swing Drive Oil Sample - Obtain
G3520B Engines MID 033 - CID 0168 - FMI 02 System Voltage intermittent/erratic
C9 Marine Engines Engine Cranks but Will Not Start
320C U Excavator Hydraulic System Oil Sample - Obtain
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.