C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Caterpillar


Cylinder Head - Inspect

Usage:

C1.5 TAF

Table 1
Required Tools    
Part Number     Part Name     Qty    
8S-6691     Cylinder Head Repair Stand     1    



Illustration 1g00907444

Bolt tightening sequence

  1. Remove the bolts in the cylinder head in the reverse sequence that is shown in Illustration 1.

    Remove the cylinder head from the engine.

  1. Clean the cylinder head thoroughly. Make sure that the contact surface of the cylinder head and the contact surface of the cylinder block are clean, smooth, and flat.

  1. Inspect the bottom surface of the cylinder head for pitting, corrosion, and cracks. Inspect the area around the valve seats and the holes for the fuel injection nozzles.



    Illustration 2g00842292

    Typical example

    (1) Cylinder head

    (2) 8S-6691 Cylinder Head Repair Stand

  1. Put cylinder head (1) on the 8S-6691 Cylinder Head Stand Set (2) .



    Illustration 3g00907448

    Typical example

  1. Use a straight edge and a feeler gauge to check the six positions of the cylinder head for distortion. Refer to Specifications, "Cylinder Head" for the requirements of flatness.

Caterpillar Information System:

C13 Engines for Caterpillar Built Machines Compression Brake
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Cooling System - Check - Overheating
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Increased Engine Oil Temperature - Inspect
C18 Generator set and C18 Marine Engines Auxiliary Water Pump - Assemble - Type 1
C18 Generator set and C18 Marine Engines Auxiliary Water Pump - Disassemble - Type 1
C11, C13 and C15 On-highway Engines System Overview
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Vehicle Speed and Speedometer Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Two Speed Axle Switch Circuit - Test
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Tachometer Circuit - Test
Supplement to the Operation and Maintenance Manual{0707} Supplement to the Operation and Maintenance Manual{0707}
3054E Industrial Engine Water Pump - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Water Pump
2003/02/03 Checking the Motor Rotation after Replacing the Blower Motor Can Increase Service Life {7304, 7320}
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Charging System - Test
3056E Industrial Engine Belt Tension Chart
C1.5 and C2.2 Engines For Caterpillar Built Marine Generator Sets Air Inlet and Exhaust System - Inspect
C9 Marine Engines System Configuration Parameters
C1.5 and C2.2 Engines for Caterpillar Built Marine Generator Sets Exhaust Manifold
G3500 A3 Engines Engine Pre-Lube Pressure (Low)
G3500 A3 Engines ECM Output Circuit (Prelubrication Oil Pump)
C1.5 and C2.2 Generator Sets Engine Warm-up
C1.5 and C2.2 Generator Sets Stopping the Engine
3054E Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
3054E Industrial Engine Inlet and Exhaust Valves - Remove and Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.