Gear Group (Front)
Show/hide table
图 1 | g02564080 |
(6) 附件驱动器的螺纹孔 |
Show/hide table
222-3088 前齿轮总成的技术规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 1 | 222-3907 齿轮 | 齿轮的齿数为 96。 |
齿轮的孔径为 |
|||
2 | - | - | 将惰轮上的正时标记对准凸轮轴齿轮上的正时标记和曲轴齿轮上的标记。 |
3 | 1 | 222-3905 齿轮组件 | 齿轮的齿数为 71。 |
齿轮中用于轴承的孔径为 |
|||
安装后轴承的孔径为 |
|||
从齿轮后面嵌入的轴承长度为 |
|||
4 | 1 | 222-3902 齿轮组件 | 齿轮的齿数 64。 |
齿轮中用于轴承的孔径为 |
|||
安装后轴承的孔径为 |
|||
从齿轮后面嵌入的轴承长度为 |
|||
5 | 1 | 187-8972 曲轴齿轮 | 齿轮的齿数为 48。 |
齿轮的孔径为 |
Caterpillar Information System:
3054E Industrial Engine Crankshaft Rear Seal - Install
C11 and C13 Engines Piston Cooling Jet
3054E Industrial Engine Camshaft - Remove and Install
C9 Marine Engines Sensors and Electrical Connectors
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Fan Override Switch Circuit - Test
C13 Engine for Combat and Tactical Vehicles Crankshaft Seals
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Diagnostic Enable Switch Circuit - Test
3126B and 3126E On-highway Engines 0022-11 Primary to Secondary Engine Speed Signal Calibration (42)
Additional Information for the Customer Communication Module (CCM) that Is Used on Series 3500 and Series 3600 Gas Applications{1926} Additional Information for the Customer Communication Module (CCM) that Is Used on Series 3500 and Series 3600 Gas Applications{1926}
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Cruise Control Switch Circuit - Test
3054E Industrial Engine Cylinder Head - Install
G3520B Engines Jacket Water to Engine Oil Differential Temperature (Low)
C1.5 and C2.2 Generator Sets Generator Lead Connections
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Ethernet Interface
C13 Engine for Combat and Tactical Vehicles Flywheel Housing
3054E Industrial Engine Crankshaft Pulley - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Housing (Front)
3054E Industrial Engine Crankshaft Front Seal - Remove
3054E Industrial Engine Crankshaft Front Seal - Install
C13 and C15 Engines for Combat and Tactical Vehicles Remote PTO Accelerator Position Sensor Circuit - Test
320B, 320B L and 320B N Excavators Swing Drive Oil Sample - Obtain
3054E Industrial Engine Piston Cooling Jets - Remove and Install
3054E Industrial Engine Fuel Priming Pump and Fuel Filter Base - Remove and Install
2003/02/03 Special Instruction, REHS1238, "Obtaining Factory Passwords and Software Enabled Attachments" is Available {7610}