Washer Pump Assemblies Must Be Primed Properly {7306}
- Caterpillar Products:
- All
The following washer pump assemblies are centrifugal pump assemblies: 7T-8890 Washer Pump As, 7T-8891 Washer Pump As, 6T-1375 Washer Pump As, 117-2826 Washer Pump As and 223-3383 Washer Pump As
Centrifugal pump assemblies are not self-priming. Centrifugal pump assemblies must be primed properly in order to operate correctly. Refer to the following procedure in order to prime a centrifugal pump assembly.
Priming Procedure
- Install the washer pump assembly and install all the hoses.
Show/hide table
Illustration 1 | g00946156 |
(1) Washer pump assembly (2) Outlet hose (3) Inlet hose |
- Fill the reservoir with washer fluid.
- Disconnect pump outlet hose (2) .
- Once fluid flows out of pump assembly (1), connect pump outlet hose (2) .
- The pump is now primed and ready for operation.
Note: If the tank is allowed to run out of fluid, the pump will need to be primed again. Follow Steps 2 through 5 in order to prime the pump.
Note: Use the appropriate antifreeze for temperatures that are below freezing.
Caterpillar Information System:
3056E Industrial Engine Vibration Damper and Pulley - Remove
3056E Industrial Engine Vibration Damper and Pulley - Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Component Location - Input/Output Cabinet
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Component Location - System Cabinet
3054E Industrial Engine Voltage Load Protection Module - Remove and Install
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0052-11 Air Inlet Shutoff Shutdown (00)
3056E Industrial Engine Valve Guide - Inspect
3126E Truck Engine Air Inlet and Exhaust System - Inspect
G3606 and G3608 Engines Exhaust Manifold
G3606 and G3608 Engines Exhaust Manifold
3126E Truck Engine Engine Oil Pressure Sensor - Test
C7 On-highway Engine Valve Mechanism Cover
3406E, C-10 and C-12 On-highway Engines 0191-07 Transmission Not Responding (68)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0054-05 Auxiliary Output #06 current low (66)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0054-06 Auxiliary Output #06 current high (66)
C7 and C9 On-Highway Engines 0173-00 High Exhaust Gas Temperature Derate
3056E Industrial Engine Cylinder Head
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0055-05 Auxiliary Output #07 current low (67)
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0055-06 Auxiliary Output #07 current high (67)
C1.5 and C2.2 Generator Sets Control Panel
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0246-11 Brake Pedal Switch #1 Fault
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0247-11 Brake Pedal Switch #2 Fault
C7 and C9 On-Highway Engines 0168-01 Low ECM Battery Power (17)
C1.5 and C2.2 Generator Sets Engine Air Cleaner Element (Single Element) - Replace