Vibration Damper and Pulley - Remove and Install
- Remove belt guard (1).
Show/hide table
Illustration 2 g01365787 - Remove nuts (3).
- Remove the vibration damper and pulley (2) from the adapter.
Show/hide table
Illustration 1 | g01365791 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 4C-5593 | Anti-Seize Compound | - |
Show/hide table
NOTICE |
---|
Thoroughly inspect the viscous damper for signs of leakage or for signs of a dented (damaged) case. Either of these conditions can cause the weight to make contact with the case. This can affect the viscous damper's operation. |
- If necessary, install the studs and tighten to a torque of
65 ± 10 N·m (48 ± 7 lb ft) . - Position the vibration damper and pulley (2) on the adapter.
- Apply Tooling (A) to nuts (3). Install nuts (3) and tighten to a torque of
135 ± 20 N·m (100 ± 15 lb ft) .Show/hide tableIllustration 4 g01365791 - Install belt guard (1).
Show/hide table
Illustration 3 | g01365787 |
Caterpillar Information System:
C7 and C9 On-Highway Engines Transmission (AT/MT/HT) Relay Circuit - Test
C9 Marine Auxiliary and Generator Set Engines Heat Exchanger - Inspect
C9 Marine Auxiliary and Generator Set Engines Fuel System Secondary Filter - Replace
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Bearing Retainer - Remove and Install
C9 Marine Auxiliary and Generator Set Engines Zinc Rods - Inspect/Replace
UPS 250 and UPS 300 Uninterruptible Power Supplies Bearing Retainer - Remove and Install
3126B and 3126E On-highway Engines 0030-13 PTO Throttle out of calibration (29)
3126B and 3126E On-highway Engines 0030-08 PTO Throttle signal invalid (29)
C9 Marine Auxiliary and Generator Set Engines Engine Oil Sample - Obtain
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0231-02 J1939 Data Incorrect (58)
C7 and C9 On-Highway Engines 0111-14 Low Coolant Level Warning
3056E Industrial Engine Crankshaft Gear - Remove and Install
3054E Industrial Engine Fan Drive - Remove and Install
3056E Industrial Engine Fuel Injection Pump - Remove
3056E Industrial Engine Fuel Injection Pump - Install
3406E, C12, C15 and C18 Marine Engines Engine Speed/Timing Sensor - Calibrate
3126B and 3126E On-highway Engines PTO Switch ON Lamp Circuit - Test
2003/02/01 A New Spark Plug Is Available For Use In Applications That Use Bio-Gas Fuel {1555}
2003/01/01 New Ignition Control Groups Are Available And A New Wiring Harness Is Available To Connect The Ignition Control Group To The Display Module For The Caterpillar Ignition System (CIS) {1550}
2002/12/01 A New Service Manual, RENR2495, "3600 Engines PanelView Monitor" is Available {0374}
2003/01/01 227-4236 Electrical Cable is Available {4459}
2003/02/01 Correction to Systems Operation/Testing and Adjusting, RENR5908-01 , "Procedure for Engine Timing" {1000, 1900}
2003/02/01 Correction to Troubleshooting, RENR5910-01 , "Engine Speed/Timing Sensor" {1907, 1912}
C7 and C9 On-Highway Engines Engine/Gear Parameters