UPS 250 and UPS 300 Uninterruptible Power Supplies Caterpillar


Bearing Retainer - Remove and Install

Usage:

UPS 250 APZ


注意

请务必将系统固定到地基上后再拆除轴承保持器。 在未固定系统之前拆除轴承保持器将会导致单元损坏。


将系统投入使用之前,必须先拆卸运输保持器,并安装工作保持器。

当搬移系统时,必须安装运输保持器。 这些保持器用于保护轴承芯子。 将保持器存放在安全的地方以备日后使用。

拆卸运输保持器


注意

只有经过培训的 Caterpillar 代理商人员才能执行本程序。





图 1g00927656

运输保持器的分解图

(3) 上保持器的两个螺栓

(4) 上运输保持器

(3) O 形密封圈

(7) 下运输保持器

(8) 下保持器的两个螺栓

  1. 拆下三块薄金属面板。 这些薄板位于系统内部。

  1. 松开并拆下上方保持器 (4) 上的两个螺栓 (3) 。 应将每个螺栓旋转四分之一圈,直到螺栓松动为止。

  1. 用手将保持器慢慢拔出。

    注: 切勿使用任何工具来拆卸保持器。 这样会损坏轴承芯子。

  1. 请将保持器存放在安全的地方,以备日后使用。

  1. 松开并拆下下方保持器 (7) 上的两个螺栓 (8) 。 应将每个螺栓旋转四分之一圈,直到螺栓松动为止。

  1. 慢慢地拔出保持器。

    注: 切勿使用任何工具来拆卸保持器。 这样会损坏轴承芯子。

  1. 请将保持器存放在安全的地方,以备日后使用。

  1. 继续进行"工作保持器的安装"。

工作保持器的安装


注意

只有经过培训的 Caterpillar 代理商人员才能执行本程序。





图 2g00927658

工作保持器

(9) 螺钉

(10) 换向传感器组件

(11) O 形密封圈

(12) 螺栓

(13) 换向传感器轮

(15) 隔圈

(14) 螺塞

(16) 螺钉

(17) 盖板

(18) O 形密封圈

(19) 工作保持器

(20) 抛光螺栓

(21) O 形密封圈

(22) 放电漏极

(23) 螺钉

  1. 将少量的 7M-7456 轴承安装固定胶 涂在螺栓 (20) 的螺纹上。

  1. 安装保持器 (19) 和螺栓 (20) 。

  1. 以 (38 牛米) 28 磅英尺的扭矩拧紧螺栓 (20)。

  1. 安装隔圈 (15) 。

  1. 将少量的 7M-7456 轴承安装固定胶 涂在螺栓 (4) 的螺纹上。

  1. 安装换向传感器轮 (13) 和螺栓 (12) 。

  1. 以 38 牛米 (28 磅英尺)的扭矩拧紧螺栓 (12) 。

  1. 将少量的 6V-2055 高真空润滑脂 涂在 O 形密封圈 (21) 上。

  1. 将 O 形密封圈 (21) 安装到漏极 (22) 上。

  1. 安装漏极 (22) 、O 形密封圈 (21) 和四个螺钉 (23) 。

  1. 将少量的 6V-2055 高真空润滑脂 涂在 O 形密封圈 (11) 上。

  1. 安装换向传感器组件 (10) 和三个螺钉 (9) 。

    注: 确保转子位置传感器正确定位。 有关定位转子位置传感器的步骤,请参阅系统操作、测试和调整, "转子位置传感器 - 调整"部分。

  1. 将少量的 6V-2055 高真空润滑脂 涂在 O 形密封圈 (18) 上。

  1. 安装 O 形密封圈 (18) 、盖板 (17) 和两个螺钉 (16) 。

  1. 向真空泵供电。 这需要使用一根加长缆线。

    注: 300 系列中的多模块单元设置为 230 VAC。

    注: 应尽快达到真空状态。 当湿度较高和/或飞轮长期打开时,真空泵可能需要数小时才能达到适当的真空度。

  1. 安装热敏电阻感测缆线。 接头配接不当会导致接头插针损坏。

  1. 安装三块金属薄板。

Caterpillar Information System:

3126B and 3126E On-highway Engines 0030-13 PTO Throttle out of calibration (29)
3126B and 3126E On-highway Engines 0030-08 PTO Throttle signal invalid (29)
C9 Marine Auxiliary and Generator Set Engines Engine Oil Sample - Obtain
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines 0231-02 J1939 Data Incorrect (58)
C7 and C9 On-Highway Engines 0111-14 Low Coolant Level Warning
3056E Industrial Engine Crankshaft Gear - Remove and Install
C18 Generator set and C18 Marine Engines Rocker Arm and Shaft - Remove
C11, C13 and C15 On-highway Engines Engine Speed/Timing Sensor Circuit - Test
3056E Industrial Engine Idler Gear - Remove and Install
G3304B and G3306B Engines Engine Oil Filter Base
3056E Industrial Engine Camshaft Gear - Remove and Install
3126B Marine Engines E096 High Fuel Pressure
C9 Marine Auxiliary and Generator Set Engines Zinc Rods - Inspect/Replace
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Bearing Retainer - Remove and Install
C9 Marine Auxiliary and Generator Set Engines Fuel System Secondary Filter - Replace
C9 Marine Auxiliary and Generator Set Engines Heat Exchanger - Inspect
C7 and C9 On-Highway Engines Transmission (AT/MT/HT) Relay Circuit - Test
C18 Generator set and C18 Marine Engines Vibration Damper and Pulley - Remove and Install
3054E Industrial Engine Fan Drive - Remove and Install
3056E Industrial Engine Fuel Injection Pump - Remove
3056E Industrial Engine Fuel Injection Pump - Install
3406E, C12, C15 and C18 Marine Engines Engine Speed/Timing Sensor - Calibrate
3126B and 3126E On-highway Engines PTO Switch ON Lamp Circuit - Test
2003/02/01 A New Spark Plug Is Available For Use In Applications That Use Bio-Gas Fuel {1555}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.