Fuel Injection Nozzles - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 239-3312 | Sealant | - |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Thoroughly clean the threads on threaded nut (1) and the cylinder head.
- Install a new seat washer (3) into the recess in the cylinder head.
Note: If the original seat washer is reused, the projection of the fuel injection nozzle will be incorrect.
- Put a bead of Tooling (A) that is
2.0 mm (0.08 inch) by6.0 mm (0.24 inch) long on the first two threads of threaded nut (1).Note: Do not allow Tooling (A) below the threads of nut (1).
Show/hide table
Illustration 2 g00903762 Show/hide table
Illustration 3 g00903704 - Put fuel injection nozzle (2) into position in the cylinder head. Make sure that the detent ball in the fuel injection nozzle (2) is aligned correctly with ball Detent (X) in the cylinder head.
Show/hide table
Illustration 4 g00902563 - Carefully tighten threaded nut (1) to a torque of
40 N·m (30 lb ft) . Remove any excess Tooling (A) from fuel injection nozzle.Note: Do not rotate the fuel injection nozzle after installation. The seal which is made by the anti-seize compound may break. A broken seal may allow leakage past the seat of the fuel injection nozzle.
Show/hide table
| |
| Illustration 1 | g00903765 |
End By:
- Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install".
Caterpillar Information System:
3056E Industrial Engine Fuel Injection Nozzles - Remove
G3520C and G3520E Generator Set Engines Cat Data Link - Test
G3520B Industrial Engine MID 036 - CID 1720 - FMI 09 Turbocharger Compressor Bypass Valve Actuator not communicating on link
G3520B Industrial Engine MID 036 - CID 1440 - FMI 09 Unable to communicate with Throttle Actuator Drv
G3408C and G3412C Engines Engine Oil Filter Base
G3406 Engines Engine Oil Filter Base
2002/12/16 New Water Seals Provide Increased Stability At Higher Temperatures {1100, 1124}
2010/10/06 New Water Seals Provide Increased Stability At Higher Temperatures {1100, 1124}
G3408C and G3412C Engines Cylinder Head
C7 and C9 On-Highway Engines ECM Memory - Test
C7 and C9 On-Highway Engines Engine Temperature Sensor Open or Short Circuit - Test
G3516B Engines Exhaust Port Temperature (High)
Test Sequence for Pencil Type Fuel Nozzles{1254} Test Sequence for Pencil Type Fuel Nozzles{1254}
C7 and C9 On-Highway Engines Air Inlet Heater Circuit - Test
G3500 Engines Exhaust Manifold - Dry
2002/12/01 New Thermocouples Are Used To Measure The Engine Exhaust Temperature {1059, 1919}
SR4 HV and SR4B HV Generators Generator Set - Test
3056E Industrial Engine Exhaust Manifold - Remove and Install - Three-Piece Exhaust Manifold
G3500 Engines Exhaust Manifold - Dry
G3520C and G3520E Engines Spark Plug
416C, 426C, 428C, 436C and 438C Backhoe Loaders Emissions Certification Film
G3408 and G3412 Engines Idler Gear Assembly
2002/11/01 A New Fuel Transfer Pump Group Is Used {1256}
3056E Industrial Engine Exhaust Manifold - Remove and Install - Two-Piece Exhaust Manifold