C15 Petroleum Generator Set Engines Caterpillar


Electric Starting Motor

Usage:

C15 115


图 1g02563097

表 1
207-1564 电起动马达总成的技术规格 
项目  数量  零件  技术规格说明 
小齿轮和壳体之间的间隙为 9.1 mm (0.36 in)。 
6V-8188 螺母  拧紧至扭矩为 30.5 ± 3.5 N·m (270 ± 31 lb in)。 
250-8279 电磁阀套件  20V 和 25 °C (77 °F) 下的耗电量:
1. 对于吸合电流为 57 安培
2. 对于保持电流为最大 16 安培 
6V-8188 螺母  拧紧至扭矩为 30.5 ± 3.5 N·m (270 ± 31 lb in)。 
6V-8378 螺母  拧紧至扭矩为 2.25 ± 0.25 N·m (20 ± 2 lb in)。 
6V-8188 螺母  蓄电池端子螺母(5)最多可使用三个电缆或导线端子。 两个端子最高不低于 0 AWG。
拧紧至扭矩为 30.5 ± 3.5 N·m (270 ± 30 lb in)。 
6V-8378 螺母  拧紧至扭矩为 2.25 ± 0.25 N·m (20 ± 2 lb in)。 
拧紧至扭矩为 8 ± 3 N·m (71 ± 27 lb in)。 
当从小齿轮端观看电起动马达时,马达顺时针旋转。
25 °C (77 °F) 时无负载
1. 转速为 7643 ± 1683 rpm
2. 电流消耗为 76.5 ± 14.5 安培
3. 电压为 23 V 

Caterpillar Information System:

C7 and C9 On-Highway Engines Check Engine Lamp Circuit - Test
2002/10/28 Examine Failed Starting Motors to Understand the Reason for Failure {1453}
C7 and C9 On-Highway Engines ATA (SAE J1587 / J1708) Data Link Circuit - Test
Test Sequence for Capsule Type Fuel Nozzles{0782} Test Sequence for Capsule Type Fuel Nozzles{0782}
C7 and C9 On-Highway Engines 0232-04 5 Volt Supply voltage low (21)
C7 and C9 On-Highway Engines 0232-03 5 Volt Supply voltage high (21)
3054E Industrial Engine Camshaft Bearings - Remove and Install
3056E Industrial Engine Piston Cooling Jets - Remove and Install
3056E Industrial Engine Crankshaft Main Bearings - Remove
3406E and C15 Marine Engines Cooling System - Check - Overheating
3054C Industrial Engine and C4.4 Marine Auxiliary Generator Set Fuel System Pressure - Test
3054C Industrial Engine and C4.4 Marine Auxiliary Generator Set Fuel System - Prime
C7 On-highway Engine Piston and Rings
3056E Industrial Engine Electric Starting Motor - Remove and Install
3056E Industrial Engine Alternator - Remove
3056E Industrial Engine Alternator - Install
2002/11/01 New Spacer For Marine Oil Pan Gaskets {1302}
C7 and C9 On-Highway Engines Engine Pressure Sensor Open or Short Circuit - Test
P16, P20, P25, P28, P40 and P60 Pulverizer Maintenance Interval Schedule
3054E Industrial Engine Flywheel - Remove
3056E Industrial Engine Flywheel - Install
P16, P20, P25, P28, P40 and P60 Pulverizer Reference Material
C7 and C9 On-Highway Engines Engine Speed/Timing Sensor Circuit - Test
3054C Industrial Engine and C4.4 Marine Auxiliary Generator Set Electrical System
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.