Customer Specified Parameters Table
Show/hide table
| Table for the Customer Specified Parameters | ||
|---|---|---|
| Parameter | Available Range or Options | Default |
| "Selected Engine Rating" | ||
| "Rating Number" | Dependent on engine power | |
| "ECM Identification Parameters" | ||
| "Vehicle ID" | 17 Digits Available characters are dependent on the service tools. |
all zeroes |
| "Vehicle Speed Parameters" | ||
| "Vehicle Speed Calibration" | 2485 to 238080 PPKM (4000 to 384000 PPM) |
"Not Programmed" |
| "Vehicle Speed CAL (J1939-Trans)" | 0 to 43000 revs per km (0 to 65000 revs per mile) | "Not Programmed" |
| "Vehicle Speed CAL (J1939-ABS)" | 0 to 6.550 | "Not Programmed" |
| "Vehicle Speed Limit" | 48 to 204 km/h (30 to 127 mph) |
204 km/h (127 mph) |
| "VSL Protection" | 1700 to TEL rpm | TEL rpm |
| "Tachometer Calibration" | 2.0 to 500.0 ppr | 134.0 ppr |
| "Soft Vehicle Speed Limit" | "Yes" "No" | "No" |
| "Low Speed Range Axle Ratio" | 0.00 to 19.99 | 0.00 |
| "High Speed Range Axle Ratio" | 0.0 to 9.99 | 0.00 |
| "Cruise Control Parameters" | ||
| "Low Cruise Control Speed Set Limit" | 24 to 204 km/h (15 to 127 mph) |
204 km/h (127 mph) |
| "High Cruise Control Speed Set Limit" | 32 to 204 km/h (20 to 127 mph) |
204 km/h (127 mph) |
| "Exhaust Brake Mode" | "Coast" "Latch" "Manual" | "Manual" |
| "Auto Retarder in Cruise (0=Off)" | 5 to 16 km/h (3 to 10 mph) |
0 km/h (0 mph) |
| "Cruise/Idle/PTO Switch Configuration" | "Set/Decel-Res/Accel" "Set/Accel-Res/Decel" | "Set/Accel-Res/Decel" |
| "Soft Cruise Control" | "Yes" "No" | "Yes" |
| "Idle Parameters" | ||
| "Idle Vehicle Speed Limit" | 2 to 24 km/h (1 to 15 mph) |
2 km/h (1 mph) |
| "Idle RPM Limit" | 700 to TEL rpm | TEL rpm |
| "Idle/PTO RPM Ramp Rate" | 5 to 1000 rpm/sec | 50 rpm/sec |
| "Idle/PTO Bump RPM" | 5 to 500 rpm | 20 rpm |
| "Fast Idle RPM 1" | 700 to TEL rpm | 1000 rpm |
| "Fast Idle RPM 2" | 700 to TEL rpm | 0 rpm |
| "Warm Up Mode Idle Speed" | 700 to 1400 rpm | 1000 rpm |
| "Dedicated PTO Parameters" | ||
| "PTO Configuration" | "Off" "Cab Switches" "Remote Switches" "Remote Throttle" | "Off" |
| "PTO Top Engine Limit" | 700 to TEL rpm | TEL rpm |
| "PTO Engine RPM Set Speed" | Low Idle rpm to PTO TEL rpm | 0 rpm |
| "PTO Engine RPM Set Speed A" | Low Idle rpm to PTO TEL rpm | 0 rpm |
| "PTO Engine RPM Set Speed B" | Low Idle rpm to PTO TEL rpm | 0 rpm |
| "PTO to Set Speed" | "Yes" "No" | "No" |
| "Maximum PTO Enable Speed" | 700 to TEL rpm | TEL rpm |
| "PTO Cab Throttle RPM Limit" | Low Idle rpm, TEL rpm, or PTO TEL rpm | TEL rpm |
| "PTO Kickout Vehicle Speed Limit" | 2 to 204 km/h (1 to 127 mph) |
2 km/h (1 mph) |
| "Maximum PTO Vehicle Speed" | 5 to 204 km/h (3 to 127 mph) |
204 km/h (127 mph) |
| "Torque Limit" | 135 N·m (100 lb ft) to Rated Torque | 2712 N·m (2000 lb ft) |
| "PTO Shutdown Time" | 3 to 1440 minutes | 0 minutes |
| "PTO Activates Cooling Fan" | "Normal" "Continuous" | "Normal" |
| "Exhaust Brake Options" | ||
| "Exhaust Brake/Warm Up Configuration" | "None" "Warm Up Only" "Exhaust Brake and Warm Up" "Exhaust Brake Only" | "Exhaust Brake Only" |
| "Engine/Gear Parameters" | ||
| "Lower Gears Engine RPM Limit" | 1500 to TEL rpm | TEL rpm |
| "Lower Gears Turn Off Speed" | 2 to 24 km/h (1 to 15 mph) |
2 km/h (1 mph) |
| "Intermediate Gears Engine RPM Limit" | 1500 to TEL rpm | TEL rpm |
| "Intermediate Gears Turn Off Speed" | 16 to 80 km/h (10 to 50 mph) |
16 km/h (10 mph) |
| "Gear Down Protection RPM Limit" | 1700 to TEL rpm | TEL rpm |
| "Gear Down Protection Turn On Speed" | 48 to 204 km/h (30 to 127 mph) |
204 km/h (127 mph) |
| "Top Engine Limit (TEL)" | Dependent on the engine rating | Dependent on the engine rating |
| "Low Idle Engine RPM" | 700 to 800 rpm | 700 rpm |
| "Transmission Style" | "Manual Option 1" "Automatic Option 1" "Automatic Option 2" "Automatic Option 3" "Automatic Option 4" "AT/MT/HT Option 1" "AT/MT/HT Option 2" "AT/MT/HT Option 3" "AT/MT/HT Option 4" | "Manual Option 1" |
| "AT/MT/HT Part Throttle Shift Speed" | "Low (80% Enable/65% Disable)" "Medium (70% Enable/55% Disable)" "High (60% Enable/45% Disable)" |
"High (60% Enable/45% Disable)" |
| "Starting Aid Output" | "Automatic" "Off" | "Off" |
| "Governor Type" | "Min/Max" "Full Range" | "Full Range" |
| "Smart Idle Parameters" | ||
| "Battery Monitor & Engine Control Voltage" | 0 to 25.5 Volts | 0 Volts |
| "Battery Monitor Low Idle Engine Speed" | 700 to TEL rpm | 1000 rpm |
| "Timer Parameters" | ||
| "Idle Shutdown Time" | 3 to 1440 minutes | 0 minutes |
| "Allow Idle Shutdown Override" | "Yes" "No" | "Yes" |
| "A/C Switch Fan-On Time" | 0 to 600 seconds | 0 seconds |
| "Fan with Engine Brake On" | "Yes" "No" | "No" |
| "Engine Monitoring Parameters" | ||
| "Engine Monitoring Mode" | "Warning" "Derate" "Shutdown" | "Warning" |
| "Engine Monitoring Lamps" | "Option 1" "Warning Lamp" | "Warning Lamp" |
| "Coolant Level Sensor" | "4-pin" "2-wire Float" "None" | "None" |
| "Oil Pressure Sensor" | "Installed" "Not Installed" | "Not Installed" |
| "Maintenance Parameters" | ||
| "Maintenance Indicator Mode" | "Off" "Automatic-Distance" "Automatic-Hours" "Manual-Distance" "Manual-Hours" | "Off" |
| "PM1 Interval (Manual Maintenance Indicator Mode)" | Manual-Distance: 8047 to 56327 km (5000 to 35000 miles) Manual-Hours: 100 to 750 hours |
Manual-Distance: 24140 km (15000 miles) Manual-Hours: 250 |
| "Engine Oil Capacity" (Automatic Maintenance Indicator Mode) | 19 to 57 L (20 to 60 qt) |
31 L (33 qt) |
| "Trip Parameters" | ||
| "Dash - PM1 Reset" | "Yes" "No" | "No" |
| "Dash - Customer Parameters" | "Yes" "No" | "No" |
| "Theft Deterrent System Control" | "Yes" "No" "Auto-Enable" | "No" |
| "Theft Deterrent Password" | Four Characters (A thru Z, 0 thru 9) |
0000 |
| "Quick Stop Rate" | 0 to 204 km/h per second (0 to 127 mph per second) | 0 km/h per second (0 mph per second) |
| "Input Selections" | ||
| "Fan Override Switch" | "None" "J1939-Body Controller" "J1939-Cab Controller" "J1939-Instrument Cluster" | "None" |
| "Transmission Neutral Switch" | "None" "J1939" "J1/P1:62" | "J1/P1:62" |
| "Exhaust Brake Switch" | "J1/P1:16" "J1939-Body Controller" "J1939-Cab Controller" "J1939-Instrument Cluster" "None" | "None" |
| "Ignore Brake/Clutch Switch" | "J1/P1:47" "None" | "None" |
| "Two Speed Axle Switch" | "J1/P1:6" "None" | "None" |
| "Vehicle Speed Input" | "J1939-ABS" "J1939-Trans" "J1/P1:32 & 33" | "J1/P1:32 & 33" |
| "PTO Engine Shutdown Switch" | "J1/P1:7" "J1/P1:23" "None" | "None" |
| "Torque Limit Switch" | "J1/P1:7" "J1/P1:23" "None" | "None" |
| "PTO Engine RPM Set Speed Input A" | "J1/P1:46" "None" | "None" |
| "PTO Engine RPM Set Speed Input B" | "J1/P1:7" "J1/P1:23" "None" | "None" |
| "Diagnostic Enable" | "J1/P1:46" "J1939-Body Controller" "J1939-Cab Controller" "J1939-Instrument Cluster" "None" | "None" |
| "Cruise Control On/Off Switch" | "J1/P1:59" "J1939-Body Controller" "J1939-Cab Controller" "J1939-Instrument Cluster" | "J1/P1:59" |
| "Cruise Control Set/Resume Switch" | "J1/P1:35 & 44" "J1939-Body Controller" "J1939-Cab Controller" "J1939-Instrument Cluster" | "J1/P1:35 & 44" |
| "Cruise Control Pause Switch" | "J1939-Body Controller" "J1939-Cab Controller" "J1939-Instrument Cluster" "None" | "None" |
| "Clutch Pedal Position Switch" | "J1/P1:22" "J1939-Body Controller" "J1939-Cab Controller" "J1939-Instrument Cluster" | "J1/P1:22" |
| "Service Brake Pedal Position Switch #1" | "J1/P1:45" "J1939-Body Controller" "J1939-Cab Controller" "J1939-Instrument Cluster" | "J1/P1:45" |
| "Accelerator Pedal Position" | "J1/P1:66" | "J1/P1:66" |
| "A/C High Pressure Switch" | "J1/P1:41" "None" | "J1/P1:41" |
| "Output Selections" | ||
| "Fan Control Type" | "None" "On/Off" "On/Off PWM" "On/Off DC" "Variable Speed Fan Option S" |
"None" |
| "PTO Active Output Configuration" | "J1/P1:19" "None" | "J1/P1:19" |
| "PTO Switch On Lamp" | "J1/P1:30" "None" | "J1/P1:30" |
| "Wait To Start Lamp" | "J1/P1:31" "None" J1939 |
"None" |
| "Fast Idle Enabled Lamp" | "None" "J1/P1:21" "J1/P1:31" | "J1/P1:31" |
| "Change Oil Lamp" | "J1/P1:30" "None" | "None" |
| "Passwords" | ||
| "Customer Password #1" | 8 Characters Available characters are dependent on the service tools. |
"Not Programmed" |
| "Customer Password #2" | ||
| "Data Link Parameters" | ||
| "Powertrain Data Link" | "None" "J1939" | "None" |
Caterpillar Information System:
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Filter
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Relief Valve
C9 Marine Auxiliary and Generator Set Engines Aftercooler Condensate Drain Valve - Inspect/Clean
C-15 Truck Engine Wastegate Solenoid
C-10 and C-12 Truck Engines Fuel System
Installation of Double Lip Wiper Seal{7562} Installation of Double Lip Wiper Seal{7562}
Installation of Vented Buffer Seal Assembly, U-Cup Seal, and Double Lip Wiper Seal for Hydraulic Cylinders{7562} Installation of Vented Buffer Seal Assembly, U-Cup Seal, and Double Lip Wiper Seal for Hydraulic Cylinders{7562}
C-15 Truck Engine Fuel Filter Base
C-10, C-12 and C-15 On-highway Engines Customer Specified Parameters Table
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Camshaft Bearing Position
C-10 and C-12 Truck Engines Air Inlet and Exhaust System
C18 Generator Set Engine Crankcase Breather - Clean
2002/08/01 2002A Service Pack 1 for Caterpillar Electronic Technician (Cat ET) is now available {0785}
G3500B Engines Electronic Control Module (ECM) - 20 Cylinders
2002/08/01 Relocation Of The Service Center For 3600 Fuel Injectors {1254}
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Alternator and Regulator
Torque Specifications Air Brake Fittings
Torque Specifications Bulkhead Nuts
Torque Specifications Ground Engaging Tool (G.E.T.) Fasteners
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Electrical System
3512B Marine Auxiliary Engine Manual Barring Group - Air Interlock
C-18 Truck Engines Engine Operation
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel System - Prime
C-15 Truck Engine Electric Starting Motor