Customer Specified Parameters Table
Show/hide table
| Table for Customer Specified Parameters | ||
|---|---|---|
| "Parameter" | Available Range or Options | Default |
| "Selected Engine Rating" | ||
| "Rating Number" "Multitorque Ratio" |
Dependent on engine power Unavailable (Standard Ratings) MT-1, MT-2, or MT-4 (Multi-Torque Ratings) |
Unavailable MT-4 (Multi-Torque) |
| "ECM Identification Parameters" | ||
| "Vehicle ID" | 17 Digits Available characters are dependent on the service tools. |
all zeroes |
| "Security Access Parameters" | ||
| "ECM Wireless Communication Enable" | Yes or No | No |
| "Vehicle Speed Parameters" | ||
| "Vehicle Speed Calibration" | 2485 to 93226 PPKM (4000 to 150000 PPM) |
8696 PPKM (14000 PPM) |
| "Vehicle Speed Cal (J1939 - Trans)" | 0 to 43000 revolutions per km 0 to 65000 revolutions per mile |
Not Programmed |
| "Vehicle Speed Cal (J1939 - ABS)" | 0 to 6.550 | Not Programmed |
| "Vehicle Speed Limit" | 48 to 204 km/h (30 to 127 mph) |
204 km/h (127 mph) |
| "VSL Protection" | 1000 to TEL rpm | TEL rpm |
| "Tachometer Calibration" | 12.0 to 500.0 pulses per revolution | 113.0 pulses per revolution |
| "Soft Vehicle Speed Limit" | Yes or No | No |
| "Low Speed Range Axle Ratio" | 1.00 to 19.99 | 1.00 |
| "High Speed Range Axle Ratio" | 1.0 to 9.99 | 1.00 |
| "Cruise Control Parameters" | ||
| "Low Cruise Control Speed Set Limit" | 24 to 204 km/h (15 to 127 mph) |
204 km/h (127 mph) |
| "High Cruise Control Speed Set Limit" | 48 to 204 km/h (30 to 127 mph) |
204 km/h (127 mph) |
| "Engine Retarder Mode" | Coast, Latch or Manual | Manual |
| "Engine Retarder Minimum VSL Type" | Hard Limit or Soft Limit | Hard Limit |
| "Engine Retarder Minimum Vehicle Speed" | 0 to 204 km/h (0 to 127 mph) |
0 km/h (0 mph) |
| "Auto Retarder in Cruise" | 0 to 16 km/h (0 to 10 mph) |
0 km/h (0 mph) |
| "Auto Retarder in Cruise Increment" | 0 to 8 km/h (0 to 5 mph) |
3 km/h (2 mph) |
| "Cruise/Idle/PTO Switch Configuration" | Set/Accel-Reset/Decel or Set/Decel-Reset/Accel | Set/Accel-Reset/Decel |
| "Soft Cruise Control" | Yes or No | Yes |
| "Adaptive Cruise Control Enable" | Disabled Enabled |
Disabled |
| "Idle Parameters" | ||
| "Idle Vehicle Speed Limit" | 2 to 24 km/h (1 to 15 mph) |
2 km/h (1 mph) |
| "Idle RPM Limit" | 600 rpm to TEL rpm | TEL rpm |
| "Idle/PTO RPM Ramp Rate" | 5 to 1000 rpm/sec | 50 rpm/sec |
| "Idle/PTO Bump RPM" | 5 to 500 rpm | 20 rpm |
| "Dedicated PTO Parameters" | ||
| "PTO Configuration" | Off Cab Switches Remote Switches Remote Throttle |
Off |
| "PTO Top Engine Limit" | 600 to TEL rpm | TEL rpm |
| "PTO Engine RPM Set Speed (0 = Off)" | Low Idle rpm to PTO TEL rpm | 0 |
| "PTO Engine RPM Set Speed A" | Low Idle rpm to PTO TEL rpm | 0 |
| "PTO Engine RPM Set Speed B" | Low Idle rpm to PTO TEL rpm | 0 |
| "PTO to Set Speed" | Yes or No | No |
| "Maximum PTO Enable Speed" | 700 rpm to TEL rpm | TEL rpm |
| "PTO Cab Controls RPM Limit" | Low idle rpm, TEL rpm or PTO TEL rpm | TEL rpm |
| "PTO Kickout Vehicle Speed Limit" | 2 to 204 km/h (1 to 127 mph) |
2 km/h (1 mph) |
| "Torque Limit" | 270 N·m (200 lb ft) to Rated Torque | 3400 N·m (2500 lb ft) |
| "PTO Shutdown Time" | 3 to 1440 minutes | 0 |
| "PTO Shutdown Timer Maximum RPM" | 600 to 2120 rpm | 2120 rpm |
| "PTO Activates Cooling Fan" | Normal, Continuous | Normal |
| "Engine/Gear Parameters" | ||
| "Lower Gears Engine RPM Limit" | 1100 to TEL rpm | TEL rpm |
| "Lower Gears Turn Off Speed" | 5 to 48 km/h (3 to 30 mph) |
5 km/h (3 mph) |
| "Intermediate Gears Engine RPM Limit" | 1100 to TEL rpm | TEL rpm |
| "Intermediate Gears Turn Off Speed" | 8 to 80 km/h (5 to 50 mph) |
8 km/h (5 mph) |
| "Gear Down Protection RPM Limit" | 1300 to TEL rpm | TEL rpm |
| "Gear Down Protection Turn On Speed" | 48 to 204 km/h (30 to 127 mph) |
204 km/h (127 mph) |
| "Top Engine Limit (TEL)" | 2120 rpm | 2120 rpm |
| "Top Engine Limit with Droop" | No | No |
| "Low Idle Engine RPM" | 600 to 750 rpm | 600 rpm |
| "Transmission Style" | Manual Option 1 Automatic Option 1 Automatic Option 2 Automatic Option 3 Automatic Option 4 Eaton Top 2 |
Manual Option 1 |
| "Eaton Top 2 Override with Cruise Switch" | Yes or No | No |
| "Top Gear Ratio" | 0.000 to 3.750 | 0.000 |
| "Top Gear Minus One Ratio" | 0.000 to 3.750 | 0.000 |
| "Top Gear Minus Two Ratio" | 0.000 to 3.750 | 0.000 |
| "Governor Type" | Min/Max Full Range |
Full Range |
| "Timer Parameters" | ||
| "Idle Shutdown Time" | 3 to 1440 minutes | 0 minutes |
| "Idle Shutdown Timer Maximum RPM" | 600 to 2120 rpm | 2120 rpm |
| "Allow Idle Shutdown Override" | Yes No Outside Temperature Based J1587 Outside Temperature Based |
Yes |
| "Minimum Idle Shutdown Outside Temperature" | −40° to 49°C (−40° to 120°F) |
49 °C (120 °F) |
| "Maximum Idle Shutdown Outside Temperature" | −40° to 49°C (−40° to 120°F) |
49 °C (120 °F) |
| "A/C Switch Fan On-Time" | 1 to 600 seconds | 0 seconds |
| "Fan with Engine Retarder in High Mode" | Yes or No | No |
| "Engine Retarder Delay" | 0.0 to 3.0 seconds | 0.0 seconds |
| "Smart Idle Parameters" | ||
| "Battery Monitor and Engine Control Voltage" | 0 to 25.5 volts | 0 volts |
| "Engine Monitoring Parameters" | ||
| "Engine Monitoring Mode" | Warning Derate Shutdown |
Warning |
| "Engine Monitoring Lamps" | Warning Lamp Option 1 |
Warning Lamp |
| "Coolant Level Sensor" | No 4-pin 2-wire Float Sensor |
No |
| "Maintenance Parameters" | ||
| "Maintenance Indicator Mode" | Off Manual Distance Manual Hours Automatic Distance Automatic Hours |
Off |
| "PM 1 Interval (Manual Maintenance Indicator Mode)" | 8050 to 56325 km (5000 to 35000 miles) 100 to 750 hours |
24140 km (15000 miles) 300 hours |
| "Engine Oil Capacity" (Automatic Maintenance Indicator Mode) | 19 to 57 L (20 to 60 qt) |
C-10, C-12: 34 L (36 qt) C-15: 38 L (40 qt) |
| "Trip Parameters" | ||
| "Fuel Correction Factor" | −63.5 to 63.5 | 0 |
| "Dash-Change Fuel Correction Factor" | Yes or No | No |
| "Dash-PM 1 Reset" | Yes or No | No |
| "Dash-Fleet Trip Reset" | Yes or No | No |
| "Dash-State Selection" | Yes or No | Yes |
| "Theft Deterrent System Control" | Yes, No, or "Auto-Enable" | No |
| "Theft Deterrent Password" | Four Characters | 0000 |
| "Quick Stop Rate" | 5 km/h per sec ( 3 mph per sec) to 24 km/h per sec (15 mph per sec) | 0 km/h per sec (0 mph per sec) |
| "Vehicle Activity Report" | ||
| "Minimum Idle Time" | 0 to 1440 minutes | 0 minutes |
| "Driver Reward" | ||
| "Driver Reward Enable" | Disabled or Enabled | Enabled |
| "Input Selections" | ||
| "Fan Override Switch" | None J1/P1:7 J1/P1:47 J1/P1:6 J1/P1:46 J1939 - Body Controller J1939 - Cab Controller J1939 - Instrument Cluster |
None |
| "Ignore Brake/Clutch Switch" | None J1/P1:47 |
None |
| "Torque Limit Switch" | None J1/P1:7 |
None |
| "Diagnostic Enable" | None J1/P1:46 J1939 - Body Controller J1939 - Cab Controller J1939 - Instrument Cluster |
None |
| "PTO On/Off Switch" | J1/P1:56 J1939 - Cab Controller J1939 - Body Controller J1939 - Instrument Cluster |
J1/P1:56 |
| "Remote PTO Set Switch" | None J1/P1:58 J1939 - Body Controller J1939 - Cab Controller J1939 - Instrument Cluster |
J1/P1:58 |
| "Remote PTO Resume Switch" | None J1/P1:60 J1939 - Body Controller J1939 - Cab Controller J1939 - Instrument Cluster |
J1/P1:60 |
| "PTO Engine RPM Set Speed Input A" | None J1/P1:6 J1/P1:46 J1/P1:58 J1/P1:60 J1939 - Body Controller J1939 - Cab Controller J1939 - Instrument Cluster |
None |
| "PTO Engine RPM Set Speed Input B" | None J1/P1:6 J1/P1:46 J1/P1:58 J1/P1:60 |
None |
| "Starting Aid On/Off Switch" | None J1/P1:6 J1/P1:7 J1/P1:46 J1/P1:47 |
None |
| "Two-Speed Axle Switch" | None J1/P1:6 J1939 - Body Controller J1939 - Cab Controller J1939 - Instrument Cluster |
None |
| "Cruise Control On/Off Switch" | J1/P1:59 J1939 - Body Controller J1939 - Cab Controller J1939 Instrument Cluster |
J1/P1:59 |
| "Cruise Control Set/Resume Switch" | J1/P1:35 & 44 J1939 - Body Controller J1939 - Cab Controller J1939 - Instrument Cluster |
J1/P1:35 & 44 |
| "Cruise Control Pause Switch" | None J1939 - Cab Controller J1939 - Body Controller J1939 - Instrument Cluster |
None |
| "Clutch Pedal Position Switch" | J1/P1:22 J1939 - Body Controller J1939 - Cab Controller J1939 - Instrument Cluster |
J1/P1:22 |
| "Retarder Off/Low/Medium/High Switch" | J1/P1:23 & 40 J1939 - Body Controller J1939 - Cab Controller J1939 - Instrument Cluster |
J1/P1:23 & 40 |
| "Service Brake Pedal Position Switch 1" | J1/P1:45 J1939 - Body Controller J1939 - Cab Controller J1939 - Instrument Cluster |
J1/P1:45 |
| "Accelerator Pedal Position" | J1/P1:66 | J1/P1:66 |
| "Vehicle Speed Input" | J1/P1:32 & 33 J1939 − Trans J1939 − ABS |
J1/P1:32 & 33 |
| "Output Selections" | ||
| "Engine Running Output" | None J1/P1:10 J1/P1:12 J1/P1:13 |
None |
| "Engine Shutdown Output" | None J1/P1:10 J1/P1:12 J1/P1:13 |
None |
| "Auxiliary Brake" | None J1/P1:12 |
None |
| "Starting Aid Output" | None J1/P1:10 J1/P1:12 J1/P1:13 |
None |
| "Air Inlet Shutoff Relay Control" | None J2/P2:13 |
None |
| "Fan Control Type" | None On/Off Three-Speed Fan Variable Speed Fan Option S |
None |
| "PTO Active Output" | None J1/P1:19 |
None |
| "Customer Passwords" | ||
| "Customer Password (1)" | 8 Digits Available characters are dependent on the service tools. |
Not Programmed |
| "Customer Password (2)" | ||
| "Data Link Parameters" | ||
| "Power Train Data Link" | None J1922 J1939 J1922 and J1939 |
J1939 |
Caterpillar Information System:
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Camshaft Bearing Position
C-10 and C-12 Truck Engines Air Inlet and Exhaust System
C18 Generator Set Engine Crankcase Breather - Clean
G3500B Engines Engine Design
3054C Engines for Caterpillar Built Machines Gear Group (Front)
3054E Industrial Engine Fuel Injection Nozzles
3408C, 3412C and 3412D High Performance Marine Engines Exhaust Manifold
C4.4 (Mech) Industrial Engine Valve Mechanism Cover
C-15 Truck Engine Water Lines
3054E Industrial Engine Crankshaft Seals
3054E Industrial Engine Connecting Rod Bearing Journal - Steel Crankshaft
3406C Industrial Engine Fuel System Secondary Filter - Replace
C-15 Truck Engine Fuel Filter Base
Installation of Vented Buffer Seal Assembly, U-Cup Seal, and Double Lip Wiper Seal for Hydraulic Cylinders{7562} Installation of Vented Buffer Seal Assembly, U-Cup Seal, and Double Lip Wiper Seal for Hydraulic Cylinders{7562}
Installation of Double Lip Wiper Seal{7562} Installation of Double Lip Wiper Seal{7562}
C-10 and C-12 Truck Engines Fuel System
C-15 Truck Engine Wastegate Solenoid
C9 Marine Auxiliary and Generator Set Engines Aftercooler Condensate Drain Valve - Inspect/Clean
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Relief Valve
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Filter
C9 Urban Transit Bus Engine Customer Specified Parameters Table
2002/08/01 2002A Service Pack 1 for Caterpillar Electronic Technician (Cat ET) is now available {0785}
G3500B Engines Electronic Control Module (ECM) - 20 Cylinders
2002/08/01 Relocation Of The Service Center For 3600 Fuel Injectors {1254}