Hydraulic System Oil Filter - Replace
Show/hide table
 |
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin. |
 |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Relieve the hydraulic tank pressure by pushing on top of breaker relief valve (1) before changing the filters.
Show/hide table
 | |
| Illustration 1 | g00906521 |
- Remove filter access cover (2) from the hydraulic tank guard.
Show/hide table
 | |
| Illustration 2 | g00906581 |
- Remove the filter covers.
- Inspect each cover seal for damage. Replace the cover seals, if necessary.
- Remove and discard the four filter elements.
- Remove oil filler cap (3) .
- Remove hydraulic tank oil filler strainer (5). Wash the strainer and the filter covers in clean, nonflammable solvent.
Show/hide table
 | |
| Illustration 3 | g00906583 |
- Install filler strainer (5) in the filler tube.
- Install four new filter elements (6) in the hydraulic tank.
Show/hide table
 | |
| Illustration 4 | g00906587 |
- Install the covers. Tighten the cover bolts to 56 ± 3 N m (41 ± 2 lb ft).
- Inspect the oil filler cap gasket. Replace the gasket if it is damaged.
- Maintain the hydraulic oil level above the "ADD COLD" mark in sight gauge (4) with the engine stopped and the bucket level on the ground. Add oil, if necessary through the filler tube.
- Install oil filler cap (3) .
Caterpillar Information System:
R1700G Load Haul Dump Hydraulic System Oil - Change
R1700G Load Haul Dump Fuses - Replace
R1700G Load Haul Dump Fuel Tank Water and Sediment - Drain
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train MID 081 - CID 0562 - FMI 09
R1700G Load Haul Dump Fuel Tank Cap and Strainer - Clean
3056E Engine for Caterpillar Built Machines Engine Oil Bypass Valve - Install
TH210 and TH215 Telehandlers Power Train Hydraulic Oil Contamination - Test
R1700G Load Haul Dump Fuel System Water Separator - Drain
R1700G Load Haul Dump Fuel System Secondary Filter - Replace
3054E Industrial Engine Camshaft
R1700G Load Haul Dump Fuel System Primary Filter - Clean/Replace
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Hydraulic Fan System
R1700G Load Haul Dump Hydraulic System Oil Level - Check
2002/07/22 Correction to Operation and Maintenance Manual , "Engine Oil and Filter (CF-4 Multigrade) - Change" {1318}
R1700G Load Haul Dump Hydraulic Tank Breaker Relief Valve - Clean
R1700G Load Haul Dump Implement and Steering Lockout (STIC Steering) - Test
R1700G Load Haul Dump Implement and Steering Lockout (Wheel Steering) - Test
D5N Track-Type Tractor Power Train Pressure Charts
Flexxaire Fan Hydraulic Actuated Fan - Disassemble
CB-434C Vibratory Compactor Fuel System - Prime
CP-533C, CS-533C, CP-563C, CS-563C, CS-573C and CS-583C Vibratory Compactors Steering System Gear Pump (Charge, Steering, Offset and Wheel Tilt)
3406E and C15 Marine Engines Turbocharger - Inspect
D5N Track-Type Tractor Power Train Relief Valve (Torque Converter Outlet) Pressure - Test and Adjust
2002/07/22 Correction to Operation and Maintenance Manual , "Engine Oil and Filter (CF-4 Multigrade) - Change - 3516B Standard Displacement Engine Only" {1318}