Alternator - Delco 27SI Caterpillar

Alternator - Disassemble

Usage:

D6D 01Y

Disassembly Procedure

Start By:

Remove the alternator from the machine. Refer to Disassembly and Assembly, "Alternator - Remove" for the machine that is being serviced.

Note: Before disassembly, clean the exterior of the alternator in order to prevent dirt from entering the unit.

Note: The illustrations of the procedures below show the 3T-6352 Alternator Gp. The procedures for the other 27-SI alternators are similar.

Show/hide table




Illustration 1	g00901387
Alternator (1) Pulley nut (2) Fan (3) Shield (5) Front Frame (Drive Frame) (6) Rear Frame (7) Rotor (8) Ball bearing (9) Screws (three) (10) Retainer (11) Screw (12) Screws (four) (13) Plate (14) Nuts (three) (15) Screw (17) "R" Terminal (18) Strap (19) Screws (two) (20) Regulator (21) Diode assembly (22) Screw (23) Nut (24) Strap (26) Nut (27) "B+" Terminal (28) Strap (29) Screw (31) Capacitor (32) Screw (33) Rectifier (35) Stator (36) Screws (four) (37) Field winding (38) Roller bearing (39) Collar (40) Collar

Remove pulley nut (1) .

Remove the pulley and fan (2) .

Remove shield (3). Remove four bolts (4). Separate front frame (5) from rear frame (6) .

Attach the puller, as shown. Remove front frame (5) from rotor (7). Remove collars (40) and (39) .

Remove three screws (9) and retainer (10). Use a puller to remove ball bearing (8) from front frame (5) .

Remove screw (11) at the "B-" terminal. Remove four screws (12). Remove plate (13) from rear frame (6) .

Remove three nuts (14). Disconnect the stator leads from rectifier (33) .

Remove screw (15) at the battery terminal of rectifier (33) .

Loosen nut (16). Remove "R" terminal (17) and strap (18) together.

Remove two screws (19) at the field winding terminals of regulator (20). Remove diode assembly (21) .

Remove screw (22) at the ground terminal of rectifier (33). Remove nut (23) at the ground terminal of regulator (20). Remove strap (24) .

Remove insulator (25) and loosen nut (26). Remove "B+" terminal (27) and strap (28) together.

Remove screw (29) and regulator (20) .

Remove screw (30) and capacitor (31) .

Remove screw (32) and rectifier (33) .

Loosen grommet (34) and remove stator (35) from rear frame (6) .

Remove four screws (36). Remove field winding (37) from rear frame (6) .

If necessary, remove roller bearing (38) from rear frame (6) .

Caterpillar Information System:

C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Starting the Engine

Alternator - Delco 27SI Alternator

3524B Engine for Caterpillar Built Machines Alternator - Remove and Install

Alternator - Delco 27SI Service Tools

Alternator - Delco 27SI General Information

Alternator - Delco 27SI Component Description

12H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Steering Cylinder

G3520B Engines E868 Gas Flow Control Valve Malfunction

G3520B Engines E867 Improper Gas Flow Control Valve Response

Alternator - Delco 27SI Normal Operation

C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft

G3520B Engines E242 Engine Overload

C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Cold Weather Starting

C-10, C-12 and C-15 On-highway Engines System Overview

Alternator - Delco 27SI Alternator - Assemble

C-10, C-12 and C-15 On-highway Engines Sensors and Electrical Connectors

C-10, C-12 and C-15 On-highway Engines Selected Engine Rating

C11, C13 and C15 On-highway Engines Cruise Control Parameters

G3520B Engines +8V Sensor Voltage Supply

C-10, C-12 and C-15 On-highway Engines Idle Parameters

C-10, C-12 and C-15 On-highway Engines Wastegate Solenoid - Test

797 Off-Highway Truck Engine Supplement Fuel Transfer Pump - Disassemble

C11, C13 and C15 On-highway Engines ECM Identification Parameters

C11, C13 and C15 On-highway Engines Security Access Parameters