C9 Marine Engines Caterpillar

Event codes alert the operator that an abnormal engine operating condition such as low oil pressure or high coolant temperature has been detected. When the event code is generated, the event is active.

Active Event Codes

An active event code represents a problem with engine operation. Correct the problem as soon as possible.

Active event codes are listed in ascending numerical order. The code with the lowest number is listed first.

When an event code is activated, the Electronic Control Module (ECM) transmits information about the code over the J1939 data link. Some J1939 devices may display the code. However, the code will be displayed with a SPN-FMI code. Refer to Troubleshooting, "Diagnostic Code Cross Reference" for a cross-reference between event codes and SPN-FMI codes.

When certain event codes are activated, the ECM also generates a flash code that will be displayed on the diagnostic lamp. Refer to Troubleshooting, "Diagnostic Code Cross Reference" for a cross-reference between event codes and flash codes.

Illustration 1 is an example of the operating range of an oil temperature sensor. Do not use the Illustration to troubleshoot the oil temperature sensor.

Illustration 1	g01117856
Example of the typical operating range of an oil temperature sensor (1) This area represents the normal temperature range for the engine oil. The normal output voltage of the sensor is 0.2 VDC to 4.2 VDC. (2) In this area, the oil temperature above 107 °C (225 °F) is higher than normal. The output voltage of the sensor will generate an event code. The sensor does not have an electronic problem. (3) In these areas, the output voltage of the sensor is too high or too low. The voltage is outside of the normal range. The electronic problem will generate a diagnostic code. Refer to Troubleshooting, "Troubleshooting with a Diagnostic Code" for additional information on diagnostic codes.

The following format is used for event codes:

EXXX Description of the event

The "E" means that the code is an event code. The "XXX" represents a numeric identifier for the event code.

Warning - This condition represents a serious problem with engine operation. However, this condition does not require a derate or a shutdown.

Derate - For this condition, the ECM reduces the engine's power in order to help prevent possible engine damage.

Shutdown - For this condition, the ECM shuts down the engine in order to help prevent possible engine damage.

Logged Event Codes

When the ECM generates an event code the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when an event code is generated:

• The hour of the first occurrence of the code

• The hour of the last occurrence of the code

• The number of occurrences of the code

Logged events are listed in chronological order. The most recent event code is listed first.

This information can be helpful for troubleshooting intermittent problems. Logged codes can also be used to review the performance of the engine.

Clearing Event Codes

A code is cleared from memory when one of the following conditions occur:

• The code does not recur for 100 hours.

• A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.

• The service technician manually clears the code.

Always clear logged event codes after investigating and correcting the problem which generated the code.

Troubleshooting

For basic troubleshooting of the engine, perform the following steps in order to diagnose a malfunction:

1. Obtain the following information about the complaint from the operator:
   • The event and the time of the event

   • Determine the conditions for the event. The conditions will include the engine rpm and the load.

   • Determine if there are any systems that were installed by the dealer or by the customer that could cause the event.

   • Determine whether any additional events occurred.

2. Verify that the complaint is not due to normal engine operation. Verify that the complaint is not due to error of the operator.

3. Narrow the probable cause. Consider the operator information, the conditions of operation, and the history of the engine.

4. Perform a visual inspection. Inspect the following items:
   • Fuel supply

   • Oil level

   • Oil supply

   • Wiring

   • Connectors

Be sure to check the connectors. This is very important for problems that are intermittent. Refer to Troubleshooting, "Electrical Connectors - Inspect".

If these steps do not resolve the problem, identify the procedures in this manual that best describe the event. Check each probable cause according to the tests that are recommended.

Trip Points for the Monitoring System

The monitoring system determines the level of action that is taken by the ECM in response to a condition that can damage the engine. When any of these conditions occur, the appropriate event code will trip.

Table 1 contains the conditions that are monitored and the default trip points for each condition. Each condition has an associated parameter. The settings for each parameter can be viewed with the Caterpillar Electronic Technician (ET). The trip points for some of the parameters can be adjusted with Cat ET.

Table 1

Monitoring System Parameters
Parameter	Action	Delay Time in Seconds			Trip Point			"Disable"
		Min	Max	Default	Min	Max	Default
"Low Engine Oil Pressure"	Warning	N/A	N/A	30	N/A	N/A	(1)	NO
	Derate	N/A	N/A	30	N/A	N/A	(1)	YES
"High Engine Coolant Temperature"	Warning	N/A	N/A	30	N/A	N/A	106 °C (223 °F)	NO
	Derate	N/A	N/A	30	N/A	N/A	110 °C (230 °F)	YES
"Engine Overspeed"	Warning	N/A	N/A	0	N/A	N/A	115% of Rated Engine Speed	NO
"High Engine Inlet Air Temperature"	Warning	N/A	N/A	30	60 °C (140 °F)	70 °C (158 °F)	70 °C (158 °F)	NO
	Derate	N/A	N/A	30	66 °C (150 °F)	80 °C (176 °F)	80 °C (176 °F)	YES
"High Transmission Oil Temperature"	Warning	1	60	10	50 °C (122 °F)	120 °C (248 °F)	95 °C (203 °F)	YES
"High Transmission Oil Pressure"	Warning	0	60	10	689 kPa (100 psi)	2900 kPa (420 psi)	2412 kPa (350 psi)	YES
"Low Coolant Level"	Warning	4	60	30	N/A	N/A	N/A	YES
	Derate	4	60	30	N/A	N/A	N/A	YES
"High Fuel Pressure"	Warning	1	30	2	N/A	N/A	(1)	YES

( 1 )

Map Dependent