Electric Starting Motor
Show/hide table
Illustration 1 | g01431943 |
Show/hide table
Illustration 2 | g01431945 |
When the electric starting motor is viewed from the drive end, the motor rotates in the following direction. ... Clockwise
No load conditions at
- Speed ... 7643 ± 1683 rpm
- Current draw ... 76.5 ± 14.5 amp
- Voltage ... 23 V
- Current draw ... 76.5 ± 14.5 amp
(1) Battery terminal
- Tighten the nut on the battery terminal to the following torque. ...
30.5 ± 3.5 N·m (22 ± 3 lb ft)
A maximum of three cable or wire terminals should be between the nuts.
(2) Ground terminal
- Tighten the nut on the ground terminal to the following torque. ...
30.5 ± 3.5 N·m (22 ± 3 lb ft)
(3) Ground terminal
- Tighten the nut on the ground terminal to the following torque. ...
2.25 ± 0.25 N·m (20 ± 2 lb in)
(4) Switch terminal
- Tighten the nut on the switch terminal to the following torque. ...
2.25 ± 0.25 N·m (20 ± 2 lb in)
The wire terminal that is on the switch terminal must be insulated with heat shrink tubing. Do not use molded terminals.
(5) Motor terminal
- Tighten the nut on the motor terminal to the following torque. ...
30.5 ± 3.5 N·m (22 ± 3 lb ft)
(6) Motor frame terminal
- Tighten the nut on the motor frame terminal to the following torque. ...
8 ± 3 N·m (72 ± 24 lb in)
Clearance between the pinion and the housing ...
Solenoid
Current draw at 20 V and
- Pull-in windings ... 57 ± 4.5 Amp
- Hold-in windings ... 16 Amp maximum
Caterpillar Information System:
3408E and 3412E Engines for Caterpillar Built Machines Electric Starting Motor
324D and 326D Excavators Machine System Specifications Track Roller Mounting
Procedure For Sealing Cracks In The Air Plenum That Are On The Top Surface Of The Cylinder Block{1201} Procedure For Sealing Cracks In The Air Plenum That Are On The Top Surface Of The Cylinder Block{1201}
CIPI UNDERCARRIAGE Arrangements: 9Q-5195, 9Q-5197, 9Q-5198, 9Q-5232, 9Q-5504, 9Q-5643, 9Q-5651, 9Q-5727, 9Q-5728, 9Q-5729, 9Q-5730, 9Q-5731, 9Q-5747, 9Q-5876, 180-4029, and 213-3892 Final Drive - Assemble
3054, 3054B and 3056 Marine Engines Rocker Shaft and Pushrod - Install
2002/02/01 New Special Instruction, REHS1178, "Operating Instructions For The 4P-4788 Electrical Converter Gp And The 4P-4789 Electrical Converter Gp" Is Available {1421}
3054, 3054B and 3056 Marine Engines Rocker Shaft and Pushrod - Remove
3512B Engine for SPF343, SPS343, and SPT343 Pumpers CAT Data Link
C7 and C9 On-Highway Engines Powertrain Data Link Circuit - Test
2002/02/01 A New Systems Operation/Testing And Adjusting Module, RENR5889, "Standby Pump Panel" Is Available {0758}
CPT372 Truck Mounted Pumper Control Panel
2002/05/01 New Starting Motors Used {1453}
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0001 FMI 11 Cylinder #1 Injector fault
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0002 FMI 11 Cylinder #2 Injector fault
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0003 FMI 11 Cylinder #3 Injector fault
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0004 FMI 11 Cylinder #4 Injector fault
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0005 FMI 11 Cylinder #5 Injector fault
2002/02/25 Introduction of a New Tappet Plug {1209}
2002/02/01 Introduction of a New Tappet Plug {1209}
C12 Marine Engines Magnetic Pickup
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Motor Control (Travel)
CIPI UNDERCARRIAGE Arrangements: 3Q6662, 6Z7861, 6Z7885, 6Z7947, 6Z7957, 6Z7999, 9Q5044, 9Q5065, 9Q5082, 9Q5090, 9Q5093, 9Q5115, 9Q5118, 9Q5126, 9Q5135, 9Q5141, 9Q5168, 9Q5175, 9Q5206, 9Q5255, 9Q5259, 9Q5268, 9Q5412, 9Q5436, 9Q5464, 9Q5514, 9Q5617, 9 Travel Motor
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers CID 0164 FMI 02 Injector Actuation Pressure signal erratic
C12 Marine Engine Cooling System - Check - Overheating