Electronic Modular Control Panel II (EMCP II) Caterpillar


Indicator for Emergency Stop (for MUI Engines)

Usage:

3406B 4JK
System Operation Description:

In order to find the cause of an emergency stop shutdown, perform the following procedure.

Test Step 1. CHECK THE EMERGENCY STOP PUSH BUTTON (ESPB).

  1. Pull out the ESPB in order to deactivate the push button. Some versions of ESPB must be turned clockwise before you pull out the ESPB.

  1. Turn the engine control switch (ECS) to the OFF/RESET position and then turn the ECS to the STOP position.

Expected Result:

The ESPB should pop out. The emergency stop indicator should be OFF.

Results:

  • OK - The system is operating correctly. The problem may be intermittent.

    Repair: Check the harness and all electrical connections of the ESPB circuit. See Testing and Adjusting, "Electrical Connector - Inspect".

    Stop.

  • ESPB NOT POPPED OUT - The ESPB does not pop out.

    Repair: Replace the ESPB.

    Stop.

  • ESPB OUT, INDICATOR FLASHING - The ESPB pops out and the emergency stop indicator is FLASHING. Go to 2.

Test Step 2. CHECK THE EMERGENCY STOP INDICATOR.

Note: The following procedure will create diagnostic codes. Clear these created diagnostic codes after troubleshooting is complete.

  1. The ECS remains in the STOP position.

  1. Disconnect the harness connector from the GSC.

  1. Temporarily install a jumper from contact "39" of the GSC to "B-". This simulates the OFF/RESET position of the ECS.

  1. Check the operation of the emergency stop indicator.

Expected Result:

The emergency stop indicator should be OFF.

Results:

  • OK - The problem is with the ESPB or the related wiring.

    Repair: Troubleshoot the circuit. See the Generator Set Wiring Diagram. Refer to Testing And Adjusting, "Schematics and Wiring Diagrams". Repair failed components or replace failed components, if necessary. Repair the wiring or replace the wiring, if necessary.

    Stop.

  • NOT OK - The emergency stop indicator is FLASHING.

    Repair: The GSC may have failed. It is unlikely that the GSC has failed. Exit this procedure and perform this entire procedure again. If the problem remains, replace the GSC. See Testing And Adjusting, "EMCP Electronic Control (Generator Set) - Replace".

    Stop.

Caterpillar Information System:

3054 and 3056 Marine Generator Set Engines Heat Exchanger - Install - 3056 Engine
3054 and 3056 Marine Generator Set Engines Heat Exchanger - Remove - 3056 Engine
Electronic Modular Control Panel II (EMCP II) Indicator for Emergency Stop (for EUI Engines)
2014/02/07 The 127-2450 Cylinder Head Kit Includes A New Cylinder Head Group {1100}
3054 and 3056 Marine Generator Set Engines Water Pump - Install - 3054 Engine
3054 and 3056 Industrial and Generator Set Engines Water Pump - Inspect
Electronic Modular Control Panel II (EMCP II) Pulse Width Modulated Sensor
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Assemble
3054 and 3056 Marine Generator Set Engines Water Pump - Remove - 3054 Engine
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Disassemble
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Swivel - Install
3054 and 3056 Marine Generator Set Engines Engine Oil Cooler - Remove and Install - 3054 Engine
3054 and 3056 Marine Generator Set Engines Heat Exchanger - Remove - 3054 Engine
2002/06/01 A New Valve Adjusting Screw Is Available {1123}
Electronic Modular Control Panel II (EMCP II) Indicator for High Water Temperature
Electronic Modular Control Panel II (EMCP II) Indicator for Low Oil Pressure
EMCPII+ for Gas Engines Indicator for Overcrank
Electronic Modular Control Panel II (EMCP II) Typical Generator Abbreviations
3054 and 3056 Industrial and Generator Set Engines Automatic Timing Advance Unit - Test
Power Module Switchgear (Low Voltage and Medium Voltage) Alarm Modules
Electronic Modular Control Panel II (EMCP II) GSC CID 0100 - FMI 02 (for MUI Engines)
Electronic Modular Control Panel II (EMCP II) GSC CID 0110 - FMI 02 (for MUI Engines)
2001/12/10 A New Kit is Available for use on Turbocharged 3054 Engines for C Series and D Series Backhoe Loaders. {1058}
Electronic Modular Control Panel II (EMCP II) GSC CID 0248 - FMI 09 (for MUI Engines)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.